background image

 

 

 

E.

a)

.

b)

.

.

E1.

E2.

COMMISSIONING

PRELIMINARY PROCEDURE

Lock the clutch and then gently move the door to the closed position
Power the garage door opener: the courtesy light will turn on, the display shows “0” 

and the control unit will 

“beep”

 once

If no instruction is given for more than 2 minutes the control unit automatically 

exits from commissioning mode and   any previous adjustment will be deleted

DOOR'S OPENING LIMIT SETTING

DOOR'S CLOSING LIMIT SETTING

 

Keep pressing “

P

” key

 (about 8 seconds)

 

         

Till the control unit 
beeps once and the 
display shows “

1

 

 

   

Press “

P

” again, 

1

” must flash

 

 

 

 

Keep pressing “

+

” key

      

Till the door has 
come to the complete 

open

 position

      

Then press “

P

” key 

again to save the setting 

 

 

Press “

-

” key till the 

display shows “

2

Press “

P

” , “

2

” 

must flash

 

Keep pressing “

-

” key

 

 

Till the door has 
come to the complete

 

closed

 position

      

Then press “

P

” key 

to save the setting 

 

 

 

The saved information has no effect if this procedure is followed to set  
door's closing limit.

The saved information has no effect if this procedure is followed to set  
door's opening limit.

WARNING

WARNING

WARNING

7

GB

GB

Summary of Contents for Gear motor 230V for sectional


















Reviews: