manualshive.com logo in svg

LG THERMA V AHNW16606B0, Installation Manual, Page: 51 / 65

Share
Download
LG THERMA V AHNW16606B0 Installation Manual Download Page 51

Piping and Wiring for Outdoor Unit

Installation Manual 

51

ENGLISH

The power cord 

connected to the outdoor unit should be complied 

withIEC 60245 or HD 22.4 S4 (This equipment shall be provided with a 
cord set complying with the national regulation. 

 

The connecting cable

 connected to the outdoor unit should be 

complied with IEC 60245 or HD 22.4 S4 (This equipment shall be 
provided with a cord set complying with the national regulation.) 

If the supply cord is damaged, it must be replaced by a special cord or assembly availible from the manufacturer of its service agent.

NORMAL CROSS-SECTIONAL AREA

20mm

GN/YL

NORMAL
CROSS-SECTIONAL
AREA 0.75 mm

2

When the connection line between the indoor unit and 
outdooor unit is over 40 m, connect the telecommunication 
line and power line separately. 

GN/

YL

1 Phase(Ø)

20 

mm

3 Phase(Ø)

20 

mm

GN/

YL

Precautions when laying power wiring

Use round pressure terminals for connections to the power terminal block.

In absence of the pressure terminals, follow the instructions below.
• Do not connect wiring of different thicknesses to the power terminal block. (Slack in the power wiring may cause abnormal

heat.)

• When connecting wiring which is the same thickness, do as shown in the correct figure as below:

Make sure that the screws of the terminal are not loosely fitted.

Round pressure terminal

Power wire

Model

Phase (Ø) Area (mm

2

)

AHNW16606B0

1

4

AHUW146A2 

6

AHUW096A3 

AHUW126A3 

AHUW146A3 

AHUW166A3

AHNW16606B0

3

2.5

AHUW128A3 

AHUW148A3 

AHUW168A3 

Two kind of cables should be connected to the outdoor unit : One is ‘Power cable’, the other one is
‘Connecting cable’. Power cable is a cable which is used to supply external electricity to the outdoor unit.
This cable is generally connected between the external power source (such as main electric power
distribution panel of user’s house) and the outdoor unit. Conversely, connection cable is used to connect
between the outdoor unit and the indoor unit to supply electric power to the indoor unit and to establish
the communication between the outdoor unit and the indoor unit. 

Procedure for wiring to the outdoor unit is performed in four steps. Before starting the wiring, check if the
wire specification is suitable and read the following directions and cautions VERY carefully.

Electrical Wiring

Summary of Contents for THERMA V AHNW16606B0


































































Reviews:

No comments