manualshive.com logo in svg

LG THERMA V AHNW16606B0, Installation Manual, Page: 4 / 65

Share
Download
LG THERMA V AHNW16606B0 Installation Manual Download Page 4

Important information 

4

Air-to-Water Heat Pump

• Read Owner’s manual and Installation manual before installation.

• Any altering or replacement of original components of the device voids the

manufacturer’s guarantee for safe and functional operation. The
manufacturer is not responsible for the consequences and will not
acknowledge claims for damages in these cases of undesignated and
incorrect use of the device. The user is solely responsible for injuries and
damages on the device itself or on other objects resulting from undesignated
and incorrect use of the device.

• The installation of the device has to be performed in accordance with the

manual; otherwise the manufacturer does not acknowledge the warranty.

• High pressure can cause to safety valve to leak water. Make sure the

drainage pipe is open to atmospheric pressure.

• Failure to comply with the manual and good practice while connecting the

device to the power supply can lead to serious injury or death.

• Connecting the device to the power source can only be performed by a

qualified personnel.

• It is prohibited to move, shift, clean or service the device while in operation.
• It is prohibited to play with the device. Children are not allowed to clean the

device without supervision.

• The device can be operated independently only by informed persons who

are familiar with the safe operation of the device and understand possible
hazards of its operation. Children older than 8 and people with reduced
physical and mental capacities and with lack of experience and knowledge
can only operate the device under the supervision of an informed person.

• Before installation and any further adjustments to the device it is necessary

to consider the manual for safe use and maintenance.

• The installation has to be performed in accordance with national regulations

on electrical installations and with the instructions of the manufacturer. It has
to be performed by a professionally trained person.

• It has to be made sure that the device does not endanger anybody. Access

Safety warnings and instructions

General

Summary of Contents for THERMA V AHNW16606B0


































































Reviews:

No comments