manualshive.com logo in svg

LG MultiSITE MS8250, User Manual

Share
Download
LG MultiSITE MS8250 User Manual Download Page 38

38

MultiSITE MS8250 V

AV Room Controllers

Due to our policy of continuous product innovation, some specifications may change without notification.  

©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG Life’s Good” is a registered trademark of LG Corp.

6/9 Configuration

Standby mode

Absolute

Standby diff.

4.0 °F

Standby time

0.5 hrs

Unocc. time

0.0 hrs

Temp. occ. time 2.0 hrs

Configuration Parameters Default Value

Significance and Adjustments

Standby Mode (Standby Mode 

Configuration)

Default Value: Absolute

Standby setpoints used for control.
Absolute: Standby entered values are used for standby mode. 

Offset: Occupied set/- Standby diff. used for standby mode.
Refer to “Setpoints Screens” on page 49 to define Standby cool and Standby heat values.
Choices: Absolute or Offset.

Standby diff. (Standby Temperature 

Differential)

Default Value: 4.0°F (2.0°C)

When Standby mode is set to “offset”, standby setpoints are calculated as follows: 

Standby cool: Cool se Standby diff. 

Standby heat: Heat setpoint - Standby diff.
Refer to “Setpoints Screens” on page 49 to define Standby cool and Standby heat values.
Range: 1.0°F (0.5°C) to 5.0°F (2.5°C), using 1.0°F (0.5°C) increments.

Standby Time

Default: 0.5 hours

Time between the moment where the motion sensor detects last movement in the area, and 

the time which the Room Controller stand-by setpoints become active.

This parameter is not active when the “Door” function is used (wired or wireless).

Range: 0.5 to 24.0 hours, using 0.5 hour increments.

Unocc. Time (Unoccupied Time)

Default: 0.0 hours

Time between the moment where the Room Controller toggles to stand-by mode, and the 

time which the Room Controller unoccupied mode and setpoints become active.

Default value of 0.0 hours disables the unoccupied timer. This prevents the Controller from being 

able to switch from stand-by mode to unoccupied mode when PIR functions are used.

Range: 0.0 to 24.0 hours (0.5 hour increments).

Temp. Ccc. Time (Temporary Occupancy

Time)

Default Value: 2 hours

The time the Room Controller stays in override mode before reverting back to unoccupied 

mode. When the Room Controller is in unoccupied mode, pressing the on-screen Over-

ride icon or closing the contact on UI17, configured as “Remote Override”, sets the Room 

Controller to Override mode for defined time period, and uses the Occupied Cooling and 

Heating setpoints.
Range: 0.0 to 24.0 hours

CONFIGURATION SCREENS

Configuration 6 / 9

Configuration 6 / 9

Figure 27: 

Configuration 6 / 9 Display.

Table 20: 

Configuration 6 / 9 Parameter Details.

Summary of Contents for MultiSITE MS8250

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands