manualshive.com logo in svg

LG MultiSITE MS8250, User Manual

Share
Download
LG MultiSITE MS8250 User Manual Download Page 19

19

User Manual

Due to our policy of continuous product innovation, some specifications may change without notification.  

©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG Life’s Good” is a registered trademark of LG Corp.

Network

BAC. IP

Optional prot.

None

Wired protocol

Onboard prot.

None

Network Settings

User can select wired BACnet / Modbus / ZigBee wireless protocol (when ZigBee feature is available).

Onboard ZigBee Detection (Read Only)

Type of Expansion Module: None, ZigBee, 

IP or BAC. IP (Read Only)

Table 2: Network Settings Parameter Details.

Configuration Parameters Default Value

Significance and Adjustments

Onboard Protocol

Read Only

Onboard ZigBee detection 

Display Readings: None, ZigBee

Optional Protocol

Read Only

Requires onboard ZigBee module or optional Wi-Fi module (VCM8002V504). 

ZigBee: ZigBee detected 

IP: Wi-Fi module detected 

BAC. IP: Wi-Fi module detected and BACnet/IP enabled 

Display Readings: ZigBee, IP or BAC. IP

Wired Protocol

Default Value: BACnet

None: No wired protocol configured 

BAC MSTP: BACnet MS/TP network protocol 

Modbus: Modbus network protocol 

Choices: None, BACnet or Modbus

NETWORK SCREENS

Network Settings

Figure 9: Network Settings Display.

Upgrade of ZigBee 2.4 to 3.0

Upgrading ZigBee 2.4 to 3.0 will not support the SEDCO2G5045 sensor. It will therefore need to be recommissioned.

There is also a new “Security Levels” parameter for the ZigBee network (see page 21):

• Low (default value) is fully backwards compatible with ZigBee Home Automation 1.2 devices, and therefore compatible with all of the sen-

sors.

• Normal (needs to be selected by user) is only compatible with ZigBee 3.0.

Wired Protocol (BACnet MS/TP or Modbus)

Summary of Contents for MultiSITE MS8250

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands