LG MULTI F MAX Engineering Manual Download Page 123

Page: 123 / 224

MULTI

MAX

MULTI

Installation and Best Layout Practices

DUCT (HIGH STATIC) INDOOR UNITS

Checking the Drainage System

1. Remove the air filter.

2. Check the drainage.

• Spray water on the evaporator.

• Verify that water flows through the indoor unit drain hose without leaking.

Figure 170:

Checking the Drainage System.

Pour Water

Drain Pump

Drain Pan

Flexible drain hose

(accessory)

Field-Installed

Drain Piping

Glue the Joint

Drain

Port

Drain Hose Connection

Use the clip (accessory)

Checking the Drain Pump

The unit uses a drain pump to remove condensate. The pump must be tested before the

system operates.
• Connect (field supplied) flexible drain hose to the field-installed drain piping; leave it as

is until the test is complete.

• Pour water into the flexible drain hose and check for leaks.

• After power wiring installation is complete, operate the drain pump to see if it sounds

and functions properly.

• After the test is complete, connect the flexible drain hose to the indoor unit drain port.

Figure 171:

Insulating the Piping.

Refrigerant Piping Insulation

Field-installed vapor and liquid refrigerant piping lines must be prop-

erly and completely covered in insulation (up to the indoor unit piping

connections). Any exposed piping may generate condensate or will

cause burns if touched. Insulation for this field-installed refrigerant

piping must have a minimum heat resistance of 248°F.

Drain Piping Insulation

Drain piping must have insulation a minimum of 7/32 inches thick.

Figure 169:

Checking the drain pump.

Liquid Piping

Connection

Insulation for Refrigerant Piping

(Field-Supplied)

Vapor Piping Connection

Insulation

(Field-Supplied)

Clamp for Insulation

(Field-Supplied)

Ensure no gaps are present.

Overlap the Insulation at the

Connection

Insulation for Refrigerant Piping

(Field-Supplied) Insulation for Field-Installed Piping

(Field-Supplied)

Insulating the Refrigerant and Drain Piping

DUCT (HIGH STATIC) | 123

Ceiling-Concealed Duct (High Static)

Due to our policy of continuous product innovation, some specifications may change without notification.

Summary of Contents for MULTI F MAX

































































































































































































































Search results

Summary of Contents for MULTI F MAX

Reviews:

LG MULTI F MAX, Engineering Manual, Page: 123 / 224

Search results

Summary of Contents for MULTI F MAX

Reviews: