manualshive.com logo in svg

LG MULTI F MAX, Engineering Manual, Page: 120 / 224

Share
Download
LG MULTI F MAX Engineering Manual Download Page 120

MULTI 

F

MAX

MULTI 

F

DUCT (HIGH STATIC) INDOOR UNITS

Factory Supplied Parts and Materials / Installation

Factory Supplied Materials

• Owner’s Manual

• Installation Manual

Selecting the Best Location

Do’s

• Place the unit where air circulation will not be blocked.

• Place the unit where drainage can be obtained easily.

• Place the unit where noise prevention is taken into consideration.

• 

Ensure there is sufficient strength to bear the load of the indoor unit.

• Ensure there is sufficient maintenance space.

• Locate the indoor unit in a location that is level, and where it can be easily connected to the outdoor unit / branch distribution unit.

Required Tools

• Level

• Screwdriver

• Electric drill

• Hole core drill

• Flaring tool set

• Torque wrenches

• Hexagonal wrench

• Gas-leak detector

• Thermometer

• Read all instructions before installing the product.  

• 

Installation work must be performed by authorized personnel and in accordance with the national wiring standards and all local 

codes.

Don’ts

• The unit should not be installed near a heat or steam source, or where considerable amounts of oil, iron powder, or flour are used.

• The unit should not be installed where sulfuric acid and flammable or corrosive gases are generated, vented into, or stored. 

• 

Avoid installing the unit near high-frequency generators  or near any equipment that generates an electromagnetic field (minimum 3-1/3 

feet away).

• Do not install the unit near a doorway.

The unit may be damaged, may malfunction, and / or will not operate as designed if installed in any of the conditions 

listed. 

Factory Supplied Parts

Part

Quantity

Image

Part

Quantity

Image

Drain Hose

One (1)

Zip Ties

Four (4)

Metal Clamp

Two (2)

Insulation for 

Fittings

One (1) Set

Washers for

Hanging

Brackets

Eight (8)

Simple

Controller

with Mode

Selection

(AKB72955816)

1

One (1)

Table 62:

 Parts Table.

For Vapor Piping For Liquid Piping

1

Simple Mode Controllers for the ceiling-concealed duct (high static) indoor units are also referenced by Model No. PQRCVCL0QW.

Due to our policy of continuous product innovation, some specifications may change without notification. 

 

©

LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG” is a registered trademark of LG Corp.

120   |  DUCT (HIGH STATIC)

Multi F and Multi F MAX Indoor Unit Engineering Manual

Summary of Contents for MULTI F MAX

































































































































































































































Reviews:

No comments