LG LZ-H050GXH0 Installation Manual Download Page 11 | Manualshive

Page: 11 / 33

background image

Installation

Installation Manual

11

ENGLISH

Installation

Selection of the best location

Read completely, then follow step by step.

Install the ventilator in the location that satisfies the following conditions.
• The place shall easily bear a load exceeding four times the indoor unit’s weight.
• The place shall be able to inspect the unit as the figure.
• The place where the unit shall be leveled.
• The place shall allow easy water drainage.(Suitable dimension “*C” is necessary to get a slope to

drain as figure.)

• The place shall easily connect with the outdoor unit.
• The place where the unit is not affected by an electrical noise.
• The place where air circulation in the room will be good .
• There should not be any heat source or steam near the unit.

In case that the unit is installed near the sea, the installation parts may be corroded
by salt, The installation parts (and the unit) should be taken appropriate anti-corro-
sion measures.

CAUTION

20 or more

Unit (mm)

minimum

hight

C

800 or more

Maintenance
space

Electric parts box

Front view

Side view

(unit : mm)

«
...
9
10
11
12
13
...
»

Summary of Contents for LZ-H050GXH0


































Reviews:

No comments

Related manuals for LZ-H050GXH0

Brand: Magnavox Pages: 19

Brand: Zibro Pages: 2

Brand: Thermoscreens Pages: 38

Brand: Enviracaire Pages: 106

Brand: Kampmann Pages: 24

Brand: CIAT Pages: 18

Brand: easymaxx Pages: 42

Climma Compact 5

Brand: Veco Pages: 30

Brand: SHE Pages: 45

Brand: Wow Pages: 68

Brand: Adler Europe Pages: 80

Brand: turbionaire Pages: 50

Brand: Friax Pages: 20

Brand: SANITY SYSTEM Pages: 36

Brand: Epurair Pages: 12

Brand: GE Pages: 32

Brand: GE Pages: 32

Perfera CVXM20A3V1B

Brand: Daikin Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands