background image

MODE

FAN

TIMER

TEMP

1

2

3

4

5

8

Air 

Purifier

(b)

FUZZY

DRY JET

ENERGY

SAVER

INDOOR

DESIRED

88 88

CLEAN

FILTER

AIR

PURIFIER

CL

10

7

(a)

MODE

FAN

TIMER

TEMP

ON/OFF

1

2

3

4

5

6

AUTO SWING

FUZZY

DRY JET

ENERGY

SAVER

INDOOR

DESIRED

88 88

CLEAN

FILTER

AIR

PURIFIER

CL

10

7

9

9

ON/OFF

-10

-

Your Panel may look like any of below mentione d panels.

OPERATION MODE SELECTION BUTTON

Select (a) Cool, (b) Energy Saver, (c) Fuzzy & (d) Dry. In dry mode, unit will run at low fan speed only

with compressor 'ON'. When compressor is 'OFF', fan will be off.

During Energy Saver mode, fan stops when compressor stops cooling. Approximately after 3 minutes

fan will turn ON to determine if cooling is needed. If cooling is not needed, the fan turns OFF again.

ON/OFF TIMER

Set the time of on/off operation. The timer can be set by the one hour for a maximum of 12 hours. In case of Auto

Restart, ON/OFF Timer is automatically cancelled.

Used to Start or Stop the Plasma Purification function.

FOR PLASMA MODEL-

AIR PURIFIER

AUTO RESTART

In failure of electric power the unit runs as previous setting operation when power returns.

FAN SPEED SELECTOR

Select the fan speed in Three steps Low / Med  / High

ROOM TEMPERATURE SETTING BUTTON

Control the room temperature within a range of 18°C to 30°C.

AUTO SWING

The vertical louver swings horizontally by the automatic system and stops when you press the button again.

SIGNAL RECEIVER

POWER (ON/OFF) BUTTON

Operation starts, when this button is pressed and stops when you press the button again.

1

2

3

4

5

6

7

8

Fan speed in two steps Low (F1) / High (F2) in select models.

Operation modes may vary in select models.

Child Lock is used to prevent children from changing the settings of the unit. It can be activated when the

unit is ON by pressing the Fan Key (4) and the Timer Key (3) simultaneously for 5-10 seconds. When the

Child Lock is active, icon 'CL' lights upon the control panel. Now,  the keys on the Control Panel and the

Remote Controller will stop working. To deactivate the Child Lock, press again the Fan Key (4) and the

Timer Key (3) simultaneously for 5-10 seconds. When Child Lock is deactivated icon 'CL' goes off on the

Display Panel.

CHILD LOCK

9

a. In case when CLEAN FILTER indication is 'ON' on the Control Panel, the Plasma Pure Filter (For select

    models) needs to be cleaned. Turn 'OFF' the unit and remove Plasma Filter by opening the grill. Then

    clean the filter and replace it back to it original position. After this close the grill and turn 'ON' the unit.

    The CLEAN FILTER indication goes 'OFF' on the Display Panel. In case it doesn't reset the unit.

CLEAN FILTER

10

b. In case when CLEAN FILTER indication is blinking on the Control Panel, the Anti-Bacteria / Deo-Air Filter

    needs to be cleaned. Turn 'OFF' the unit and remove the filter by opening the grill. Then clean the filter

     and  replace  it  back  to  the  original  position.  After  this  close  the  grill  and  turn  'ON'  the  unit.  Then  press

     the  Temperature  Down  key  (5)  continuously  for  5  seconds.  The  CLEAN  FILTER  indication  goes  'OFF'

    on the Control Panel.

FUZZY

DRY JET

ENERGY

SAVER

INDOOR

DESIRED

88 88

CLEAN

FILTER

AIR

PURIFIER

CL

10

9

(c)

TIMER

FAN

SPEED

MODE

AUTO

SWING

TEMP

ON/OFF

1

5

6

4

3
7

2

Summary of Contents for LWA3BP2A







































Reviews: