LG KG195 Service Manual Download Page 75

Page: 75 / 199

- 74 -

6. Repairing

LGE Internal Use Only

Only for training and service purposes

2. Channel selection conditions

Verify that there is no interference from other radio devices or neighboring measurement systems in the

frequencies to be used for the test. If there is interference, select the test channels within the range of the

following channels. Especially in case of bit error tests, make sure that there is no influence from outside

before the test. If necessary, use a shielded box or take other channel measures.

3. Product Specification

Based on GSM 11.10-1 / 3G TS 51.110

4. Measurement adapter

Dummy battery

Dummy battery should be used shown as follows:

Test SIM card

In confidence test, general Phase2 (or ) test SIM should be used.

RF connector and RF cable

RF connector and RF cable should be used for RF test

PC-Link cable

PC-link cable (Serial Link Cable) should be used.

E-GSM

DCS1800

PCS1900

Lch

975ch to 980ch

513ch to 523ch

512ch to 522ch

Mch

60ch to 65ch

690ch to 710ch

657ch to 667ch

Hch

120ch to 124ch

874ch to 884ch

800ch to 810ch

Summary of Contents for KG195




























































































































































Search results

Summary of Contents for KG195

Reviews:

Related manuals for KG195

Brands by name

Popular brands

LG KG195, Service Manual

Search results

Summary of Contents for KG195

Reviews:

Related manuals for KG195

Brands by name

Popular brands