LG KG195 Service Manual Download Page 83

Page: 83 / 199

- 82 -

6. Repairing

LGE Internal Use Only

Only for training and service purposes

Test item

MODE

Procedure

Close down

DCS1800

( Test is repeated under DCS1800 band )

1. Push “END Call” of GSM tester

2. Wait to indicate “Call End” and change to idle screen.

3. Push “Power” to check shut down.

Band Change

E-GSM /

1. Change mode of GSM tester to “PCS1900”.

DCS1800->

2. Set HHP to PCS1900 mode using PTE Command

PCS1900

UsePTEcommand 00140 => SetBandSelect,1

Call setup

PCS1900

1. Input the PTE command “StartCall”

2. input the PTE command “Receivecall”

3. Wait to indicate “Active” to establish call

TX Power

PCS1900

1. ARFCN is assign to Mch ( or Lch/Hch )

2. Set PL to 0(PCS1900)

3. Wait to establish hand over

4. Measure output power

RMS Phase error

PCS1900

1. ARFCN is assigned to Mch ( or Lch/Hch )

2. Set PL to 0(PCS1900)

3. Wait to establish hand over

4. Change mode of GSM tester to “Phase/FREQ”

5. Set analyze burst number to 50

6. Read “RMS maximum” window

PEAK Phase error

PCS1900

1. ARFCN is assigned to Mch ( or Lch/Hch )

2. Set PL to 0(PCS1900)

3. Wait to establish hand over

4. Change mode of GSM tester to “Phase/FREQ”

5. Set analyze burst number to 50

6. Read “PEAK maximum” window

Frequency Error

PCS1900

1. ARFCN is assigned to Mch ( or Lch/Hch )

2. Set PL to 0(PCS1900)

3. Wait to establish hand over

4. Change mode of GSM tester to “Phase/FREQ”

5. Set analyze burst number to 50

6. Read “Frequency error maximum” window

Power Vs Time

PCS1900

1. ARFCN is assigned to Mch

2. Set PL to 0(PCS1900)

3. Wait to establish hand over

4. Change mode of GSM tester to “Power Ramp”

5. To check pass/fail indication under three mode “TOP

2dB” “Rise edge” and “Fall edge”

RX Class2 RBER

PCS1900

1. ARFCN is assigned to Mch*1

2. Set PL to 0(PCS1900)

3. Wait to establish hand over

4. Change mode of GSM tester to “Bit error”

5. To define sampling value to 10000

6. To define measure “Res Type 2”

7. To adjust base station output level to -103.5dBm

8. Wait to indicate BE Ratio and read it.

RX Level

PCS1900

1. Same setting and procedure as RX RBER

2. Wait to indicate “Mobile reported Rxlev” and read it.

RX Quality

PCS1900

1. Same setting and procedure as RX RBER

2. Wait to indicate “Mobile reported RX Qual” and read it.

Close down

PCS1900

1. Push “END Call” of GSM tester

2. Wait to indicate “Call End” and change to idle screen.

3. Push “Power” to check shut down.

*1 Refer to 1.Overview Channel selection condition

Summary of Contents for KG195




























































































































































Search results

Summary of Contents for KG195

Reviews:

Related manuals for KG195

Brands by name

Popular brands

LG KG195, Service Manual

Search results

Summary of Contents for KG195

Reviews:

Related manuals for KG195

Brands by name

Popular brands