LG GHX-308A/616 Installation And Programming Manual Download Page 37 | Manualshive

Page: 37 / 109

background image

GHX-308A/616
HYBRID KEY TELEPHONE SYSTEM

Http://suryawardana.com

37

timer will be activated. (Program Code: Flash 07)

4. Unsupervised multi-line conference will be dropped if the initiator does not re-enter within

unsupervised conference time.

DIAL SENDING

Description
DTMF/Pulse Sending

CO lines can be programmed to send dial pulse or DTMF(tone) signal. In case of Pulse CO line, Dialing Speed and
Make/Break Ratio are programmable per each CO line.

Pulse-to-Tone Switch-over

When commanded, the system will change the signaling on a CO line from dial pulse to DTMF (tone), allowing the use
of common carriers behind a dial pulse CO line. This can be done manually when dialing, or can be stored within a
speed dial number.

Operation

1. When using speed dial numbers, the TRANS button is used to store a switch-over

command. When activated, it will automatically insert a pause and switch over to DTMF
sending for a remaining digits.

2. The switch-over is activated manually by dialing the "*" (asterisk) when dialing.

Programming

1. Flash 05:   Pause Timer
2. Flash 30, Page A, Button 1:   Dial Signaling DTMF/PULSE
3. Flash 30, Page A, Button 5:   Pulse Ratio 60-40/66-33
4. Flash 30, Page A, Button 6:   Pulse Speed 10 PPS/20 PPS

Related Feature

1. Automatic Pause Insertion with Speed Dial
2. Station/System Speed Dial

Conditions

1. The pause length is determined by the System Pause Timer.

DIALING PRIVILEGES (Class of Service)

Description

The  system  provides  a  flexible  means  of  providing  toll  or  dialing  restriction.  Through  the  assignment  of  Class  of
Service(COS) many combinations of allow and deny numbers can be set.   Each station is assigned one of the six(6)
Classes of Service (Day and Night).
The 6 classes are,

COS

Description

1

Unrestricted.

2

Governed by Toll Allow/Deny Table A.

3

Governed by Toll Allow/Deny Table B.

4

GHX-308A : No '0' as the first digit.
GHX-616: No '0' or '1' as the first digit, maximum 7 digits.

5

Intercom calls and Paging only.

6

Receiving calls and Paging only.

Programming

1. Flash 40, Page B, Button 2: Station COS

«
...
35
36
37
38
39
...
»

Summary of Contents for GHX-308A/616














































































































Reviews:

No comments

Related manuals for GHX-308A/616

W60P Telesystem

Brand: Yealink Pages: 2

Brand: Yealink Pages: 2

Brand: Yealink Pages: 2

CP930W Telesystem

Brand: Yealink Pages: 14

Brand: Yealink Pages: 2

Brand: Panasonic Pages: 88

Brand: Yealink Pages: 4

Brand: TANDBERG Pages: 12

Brand: T-Mobile Pages: 16

Brand: audiophony Pages: 27

980590-0403 - Cordless Internet Handset USB VoIP Wireless Phone

Brand: Logitech Pages: 2

Brand: Roadstar Pages: 80

Brand: AT&T Pages: 99

Brand: Grundig Pages: 70

myPhone Jazz 202112

Brand: mPTech Pages: 65

Brand: Serene Pages: 2

S4070 Duo 4-core

Brand: ALIGATOR Pages: 17

Auto-Attendant System

Brand: Yosin Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands