LG GHX-308A/616 Installation And Programming Manual Download Page 53 | Manualshive

Page: 53 / 109

LG GHX-308A/616 Installation And Programming Manual Download Page 53

GHX-308A/616
HYBRID KEY TELEPHONE SYSTEM

Http://suryawardana.com

53

Description

When  all  the  CO  lines  allowed  to  access  are  busy,  stations  can  be  placed  in  queue  awaiting  a  line  to  become
available.  Users  are  signaled  when  the  line  is  available.  If  a  station  doesn't  answer  the  queue  signal  within  15
seconds, that station is dropped from the queue.

Operation
Queue Request

- After receiving busy tone, press CALL BACK button. You will hear confirmation tone. Then you

can see a special display in your LCD and your CALL BACK button will be lit steady.

Queue Recall

When a CO line of the group that you queued is idle, you hear queue recall ring. The queue recall can be answered;

- by pressing the line button.
- by going off-hook with Ringing Line Preference answer.

Queue Cancel

1. Press MON button.
2. Press CALL BACK button and CALL BACK button is extinguished.

Feature Code

1. TRANS 756 : (4 Button) CO Line Queuing
2. 756 :

(SLT) CO Line Queuing

REDIAL

Description

The system allows following 3 (4 in GHX-616) kinds of Redial. Up to 32 digits can be stored.

1) Dial Memo
2) Last Number Redial
3) Save Number Redial
4) Automatic Call Number Redial (GHX-616 only)

Operation

To redial the number;

- To dial the last number dialed lately on a CO line, dial Last Number Redial code.
- To dial the save number on a CO line, dial Save(Memo) Number Redial code.

Last Number Redial

Redial the last telephone number dialed on a CO line. Up to 32 digits can be stored. CO line selection is automatic.

Save Number Redial

Any number dialed on a CO line can be saved permanently to be used at any time by pressing the SPEED button
twice before terminating the call. To dial the saved number, press “SPEED#”.

To save the number;

If you wish to save a number you dialed:

- Before terminating the call, press SPEED button twice.

If you wish to save a number during CO conversation:

1. During CO conversation, press pre-programmed Dial Memo button.
2. Dial the number you wish to save with dial pad.
3. Press pre-programmed Dial Memo button again.
4. This feature does not have any influence on CO conversation.

To display a saved number;

- Press pre-programmed Dial Memo button while on-hook.

«
...
51
52
53
54
55
...
»

Summary of Contents for GHX-308A/616














































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands