manualshive.com logo in svg

LG GHX-308A/616, Installation And Programming Manual

Share
Download
LG GHX-308A/616 Installation And Programming Manual Download Page 28

GHX-308A/616 
HYBRID KEY TELEPHONE SYSTEM 

Http://suryawardana.com 

28

 

Description 
An external alarm device may be connected to the system to signal an alarm condition to stations programmed to receive 
the signal. The system detection may be programmed for either an open or closed loop and for either a continuous signal 
or single tone alarm. This feature is not available in GHX-308A.  

Operation 
To reset the alarm, while receiving the alarm signal, remove the alarm condition first and then dial the Alarm Reset code 
on any station.  

Feature Code 
1. 

775 :  Alarm Reset  

Programming 
1. 

FLASH 40, Page A, Button 8 : Alarm/Phone Box Signal Receive Yes/No 

2. 

FLASH 21, Button 1 :  

Alarm Enable/Disable 

3. 

FLASH 21, Button 2 :  

Signal Repeat/Once 

4. 

FLASH 21, Button 3 :  

Loop Detect Close/Open  

Conditions 
1. 

The continuous alarm signal will continue until the alarm condition removed. Once the alarm condition   
is cleared, the alarm signal is reset by dialing the reset code "775". 

2. 

The single alarm signal will sound only once, it will wait for the alarm condition to be removed.       

If not removed within fifteen(15) seconds, the single alarm will be repeated. 

3. 

The warning signal is presented to the station programmed.   

ATTENDANT

    

Attendant Disable Outgoing CO Line Access

 

Description 

This feature allows the attendant station to dial a code and disable CO lines from dialing to outside. This applies to all 
stations that have access to the lines. Incoming calls are not affected.  

Operation 

1. At the attendant, dial Disable Outgoing CO Line Access code. 
2. Press CO buttons to disable, then CO LEDs at attendant will flash. 
3. Press flashing CO button (LED off) again to restore outgoing access. 
4. Go on-hook.  

Feature Code 

1. 740 : (Attendant) Disable Outgoing CO Line Access  

Conditions 

1. Only CO lines for which the attendant has direct appearances can be disabled for outgoing  

access.   

Attendant Override

  

Description 
The attendant may interrupt stations in the DND mode by dialing the Call Wait code.  

Operation 
1. 

After receiving DND tone, dial Call Wait code "3". 

2. 

Wait for station to answer.  

Feature Code 
1. 

3 : 

Call Wait  

Summary of Contents for GHX-308A/616














































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands