background image

E-8

WHEN USING A SECONDARY CONTROLLER

* If your PC has an additional IDE controller on the motherboard or in a system slot, each

IDE device connected to the secondary IDE controller must also be set to the Master or
Slave mode. If you are connecting your DVD-ROM drive to a secondary IDE port, and it
is the 1st device you are connecting to it, then set the DVD-ROM jumper to the Master
position. If it is the 2nd device, set the DVD-ROM jumper to the Slave position.

* Depending on the IDE card and whether the DVD-ROM drive is a master or slave

unit, the diagram below represents the different ways in which the DVD-ROM may
be configured in your PC. The table below the diagram shows the possible Jumper
placements that would correspond to each of the different configurations shown.

Secondary IDE
Controller CARD

Hard Disk Controller Card
(This card may be a connector on the Motherboard)

Secondary IDE Channel
on Card or Motherboard

Primary IDE Channel

Secondary Master

(Hard Disk or

DVD-ROM Drive)

Secondary Slave

(Hard Disk or

DVD-ROM Drive)

Primary Slave

(Hard Disk or

   DVD-ROM Drive)

Primary Master

(Hard Disk for

Boot-up)

Card Slot

Motherboard

Figure 5. Possible System Configuration

If you have the system with two IDE channels (in the case of an enhanced IDE PC),
do not install an IDE controller card in your system.

IDE Controller

Primary (1st IDE card)

Secondary (2nd IDE card)

Secondary (2nd IDE card)

PC Manual says use CSEL

DVD-ROM Connection

Jumper Placement

Slave(Hard disk is Master)

SLAVE (default)

Master(1st device on 2nd IDE Card)

MASTER

Slave(2nd device on 2nd IDE Card)

SLAVE (default)

CSEL

Summary of Contents for DRD-841B

















Reviews: