manualshive.com logo in svg

LG ARWN038GA2, Installation Operation & Maintenance, Page: 79 / 92

Share
Download
LG ARWN038GA2 Installation Operation & Maintenance Download Page 79

79

Error Codes

Due to our policy of continuous product innovation, some specifications may change without notification.  

©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG” is a registered trademark of LG Corp.

ERROR CODE TABLES

Error Codes

• Indicate different types of unit failures, assists in self-diagnosis and 

to track the frequency of occurrence.

• Error codes are shown on the LED of indoor units, wired remote 

controller, the water source unit control board, and LG Monitoring  

View (LGMV) Diagnostic Software.

• If two or more errors occur simultaneously, the lower error code 

number is displayed first.

• After error is resolved, the error code does not display.

Table 34: Error Codes.

Error Code

Description

Details

Indoor Unit

0 1

- Indoor unit return air or optional remote wall tempera-

ture sensor communications error.

Indoor unit air temperature sensor has disconnected or short 

circuited. (Check the wiring, connection at the CN Room socket 

on the indoor unit PCB, then check the thermistor.)

0 2

- Indoor unit inlet pipe temperature sensor communica-

tion error.

Indoor unit inlet pipe temperature sensor has disconnected or 

short circuited. (Check the connection at the CN-PIPE/IN socket 

on the indoor unit PCB, then check the thermistor.)

0 3

- Communication error between zone controller and 

indoor unit.

Indoor unit PCB has not received communications signal from 

zone controller.

0 4

- Indoor unit drain pump error.

Drain pump and/or flow switch is/are malfunctioning. Also check 

drain line for obstructions.

0 5

- Communication error between water source unit and 

indoor unit.

• Indoor unit has not received communications signal from water 

source unit. 

• Check indoor unit to water source unit communication cable for 

issues (Check A terminals are connected to indoor unit A and 3 

(5 on 3 x 3 cassette) terminals; B connect to B or 4 (6 on 3 x 3 

cassette) terminals.

0 6

- Indoor unit outlet pipe temperature sensor error.

Indoor unit outlet pipe temperature sensor has disconnected 

or short circuited. (Check the connection at the CN-PIPE/OUT 

socket on the indoor unit PCB, then check the thermistor.)

0 7

- Indoor units are not operating in the same mode.

Different operation mode between indoor units.

0 9

- Indoor unit EPROM error.

• Communication error between the indoor unit PCB board and 

its option card. (The option card is about 1′ x 1′ and is plugged 

into the indoor unit PCB board. Check the connection between 

the two.)

• Communication error between EPROM chips on the indoor unit 

main PCB.

• Indoor unit EPROM data is not available.

1 0

- Indoor unit BLDC fan motor communications error.

• Fan motor has been removed or is defective. Use the OHM and 

voltage check charts in the product service manual.

• The system has detected the fan motor is not spinning. 

• On new installs, verify the installation manual and paperwork 

were removed from the fan discharge shroud before the unit 

was installed. 

• Check the wiring plug and connection at sockets CN-MOTOR1 

and CN-MOTOR2 (if used).

W

ater Source Unit

2 1 1 Water source unit inverter compressor PCB error.

• Water source unit inverter compressor PCB error. 

• Under voltage

• 

Refrigerant flow restriction from defective LEV or clogged strainer.

• Refrigerant charge is too high (overcharge). 

2 2 1 Water source unit inverter board input overcurrent 

(RMS) error.

• Overcurrent of water source unit inverter board PCB.

• Under voltage

• 

Refrigerant flow restriction from defective LEV or clogged strainer. 

• Refrigerant charge is too high (overcharged). 

Error Display

The first and second number on the LED indicates error number; the 

third number on LED indicates water source unit number.
Example: 01 = Error No. 1 on water source unit 1

Error Code Nomenclature Definitions

• MICOM: Non-volatile memory chip where unit setup information is 

stored.

• EPROM: Non-volatile memory chip where device identification, 

size, and factory defined default component operating parameters 

are stored.

For detailed information on how to troubleshoot each error, see the Water Mini Service Manual on www.lg-vrf.com.

Summary of Contents for ARWN038GA2





























































































Reviews:

No comments