manualshive.com logo in svg

LG ARWN038GA2, Installation Operation & Maintenance, Page: 63 / 92

Share
Download
LG ARWN038GA2 Installation Operation & Maintenance Download Page 63

63

Pre-commissioning and Maintenance

Due to our policy of continuous product innovation, some specifications may change without notification.  

©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG” is a registered trademark of LG Corp.

1.  Verify all that all indoor units connected to the system have power to the PCB board AND all zone controller system start buttons are OFF. 

2.  Remove the maintenance access panel and unit control box cover from the water source unit. Place panels and screws in a secure area. 

3.  Verify the communications cable between the indoor units and the water source unit is terminated at the water source unit terminals 

IDU(A) and IDU (B). 

4.  Verify the shield on the communications cable is grounded at the water source unit. 

5.  At the water source unit PCB, verify all DIP switches are “OFF” on DIP switches SW01B and SW02B. 

6.  Cycle power on the water source unit. Leave disconnect in the "ON" position. 

7.  Check the water source unit current configuration code(s). Observe the unit setup codes using the LED display found on the water source 

units PCB. Each code will display for two (2) seconds.

Preparing the Electrical System / Indoor Unit Auto Addressing

PRE-COMMISSIONING

While this routine runs, the unit runs a self-diagnostics check. At completion, the LED should be clear and nothing displayed. Diagnostic 

process should take from three (3) to seven (7) minutes.

Note:

Sequence

Code

Description

1

-

Model code

2

-

Total capacity in horsepower

3

2

Heat pump model

4

25

Normal mode display

(If the DIP switch is not set correctly, this

number is not displayed.)

5

136

Model type (Water Mini)

Model Code

Capacity

(Horsepower / Tons) Power Supply Refrigerant

120

4 / 3.0

1Ø, 208/230V

R410A

121

5 / 4.0

122

6 / 4.4

Table 29: Code Display Sequence.

Table 30: 

Water Mini Unit Model Identification Codes.

During the pre-commissioning process, do not change any DIP switch settings. All switches should be left in the OFF position on both DIP 

switches SW01B and SW02B. 

Note:

Disconnects should only be operated by a properly licensed electrician at this time. Never look at a disconnect switch when closing. Turn away 

from the switch when closing. Incorrect wiring could cause the disconnect to explode, physical injury, and / or death.

If the Auto Address Procedure has never been successfully completed for the water source system, the compressor(s) will not start when power 

is applied to the unit.

Note:

Initiate the Auto Addressing Procedure

Prepare the Electrical System

Verify correct, clean, specified power is at the line side of each system component’s disconnect. 

1.  Note if the green LED light on the component PCB board is illuminated.

2.  If a Dynamic V-8 VL air cleaner is installed on a high static ducted model indoor unit, verify power has been provided to the air cleaner 

controller. Verify by observing the LED in the center of the disconnect plate is illuminated. 

3.  If a zone controller (Remote Unit controller on the Hydro Kit) is connected to the component, verify the LCD screen displays current 

operational characteristics.

Indoor Unit Auto Addressing

Summary of Contents for ARWN038GA2





























































































Reviews:

No comments