manualshive.com logo in svg

LG ARWN038GA2, Installation Operation & Maintenance, Page: 77 / 92

Share
Download
LG ARWN038GA2 Installation Operation & Maintenance Download Page 77

77

Error Codes

Due to our policy of continuous product innovation, some specifications may change without notification.  

©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG” is a registered trademark of LG Corp.

Additional screens can be accessed by tabs on the main screen.  

Additional screens include the following: 
1.  Cycleview: Graphic of internal components including:

• Compressors showing actual speeds
• EEVs
• IDUs
• Temperature and pressure sensors
• Four-way reversing valve 

2.  Graph: Full screen graph of actual high and low pressures and high 

and low pressure limits. A sliding bar enables user to go back in 

time and view data. 

3.  Control FTN: Enables user to turn on IDUs in 1.8°F increments. 

4.  Useful Tab

• Unit Conversion: Converts metric values to imperial values. 

• Actual inverter compressor speed
• Target inverter compressor speed
• Actual superheat
• Target superheat 
• Actual subcooler circuit superheat 
• Target subcooler circuit superheat 
• Main EEV position
• Subcooling EEV position
• Inverter compressor current transducer 

value

• Outdoor air temperature
• Actual high pressure/saturation temperature
• Actual low pressure/saturation temperature
• Suction temperature
• Inverter compressor discharge temperature
• Upper outdoor coil pipe temperature
• Lower outdoor coil pipe temperature
• Liquid line pipe temperature
• Subcooler inlet temperature
• Subcooler outlet temperature
• Four-way reversing valve operation  

indicator light

• Pressure graph 

showing actual 

low pressure and 

actual high  

pressure levels

• Error code display
• Operating mode 

indicator

• Target high  

pressure

• Target low  

pressure

• PCB (printed  

circuit board) 

version

• Software version
• Installer name
• Model number
• Site name
• Total number of connected IDUs
• Communication indicator
• IDU capacity
• IDU operating mode

• IDU fan speed
• IDU EEV position
• IDU room temperature
• IDU inlet pipe temperature
• IDU outlet pipe temperature
• IDU error code

LG MONITORING VIEW (LGMV)  

DIAGNOSTIC SOFTWARE

LGMV software allows the service technician or commissioning agent to connect a computer USB port to the water source unit (WSU) main 

printed circuit board (PCB) using an accessory cable without the need for a separate interface device. The monitoring screen for LGMV  

allows the user to view the following real time data on one screen:

Figure 69: MV Real-time Data Screen.

Figure 70: MV Cycleview.

Note:

Images on these pages are examples of LGMV screenshots. Actual images may differ depending on the version of the software and the units 

installed.

Summary of Contents for ARWN038GA2





























































































Reviews:

No comments