LG ARWN038GA2 Installation Operation & Maintenance Download Page 20

Page: 20 / 92

MUL

TI V W

ater Mini System Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

All referenced materials are to be field-supplied. Images are not to scale, are for reference only, and are not intended to be used for design

purposes.

• Securely fasten all four (4) corners to the

supporting base.

• If not otherwise directed by the structural

engineer or local codes, Use a 7/16 inch or

1/2 inch diameter J-bolt. Use a hexagon nut

with a spring washer.

• Include anti-vibration material chosen by the

acoustics engineer.

• Include enough space for refrigerant piping

and electrical wiring when installing through

the bottom of the unit.

• Use an H-beam, concrete support, or other

acceptable support structure designed by a

structural engineer.

Unit: Inch

Nut

Spring Washer

Unit Mounting

Foot

Anti-vibration

Material

Four Bolts

Required

H-Beam

Concrete

Base

Three Threads

Note:

Figure 10: Close up of Anchor Bolts.

Location of the

anchor bolts

13-15/16

15-1/4

Unit: Inch

Fron

Figure 9: Location of the Anchor Bolts.

•

When building a base support for the water source unit, ensure that the floor surface / location has enough strength to support the

weight of the unit, and enough space for pipes and wiring.

•

Install the water source unit to a base and in a manner approved by the structural engineer to minimize damage to the unit in the event

of an earthquake. Any deficiency in installation may cause unit to fall, resulting in physical injury or death.

Anchoring the Water Source Unit

General Mounting

Securely attach the water source unit to a concrete pad, base rails, or other mounting platform that is anchored to the building structure.

Avoid placing the unit in a low lying area where water may accumulate. Refer to dimensional drawing in the “Product Data” section on page

10, and follow the applicable local code for clearance, mounting, anchor, and vibration attenuation requirements.

General Mounting / Anchoring the Water Source Unit

INSTALLATION

Plan View

Side View

Summary of Contents for ARWN038GA2





























































































Search results

Summary of Contents for ARWN038GA2

Reviews:

LG ARWN038GA2, Installation Operation & Maintenance, Page: 20 / 92

Search results

Summary of Contents for ARWN038GA2

Reviews: