LG ARWN038GA2 Installation Operation & Maintenance Download Page 78

Page: 78 / 92

MUL

TI V W

ater Mini System Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

5. Data

• Data Saving Start: Recording of real time data to a separate file created to be

stored on the user’s computer.

• Data Loading Start: Recorded data from a saved “.CSV” file can be loaded to

create an LGMV session.

6. Monitoring

• Electrical: The lower half of main screen is changed to show Inverter

Compressor Amps, Volts, Power Hz, Inverter control board fan Hz.

Figure 71: MV Control Indoor Units Screen.

The software is available in a high version with all of the features listed above. The low version has all features as the high version without

Target High Pressure and Target Low Pressure values shown on main screen.

In lieu of connecting to the WSU, user has the option to connect to IDU with the use of a USB to RS-485 connector kit. When connected

through IDU, user will not be able to record data.

This software can be used to both commission new systems and troubleshoot existing systems. LGMV data can be recorded to a “.CSV” file

and emailed to an LG representative to assist with diagnostic evaluations.

Recommended Minimum PC Configuration:

LG MONITORING VIEW (LGMV)

DIAGNOSTIC SOFTWARE

Error Codes

LGMV software helps the service technician or commissioning agent

to troubleshoot system operation issues by displaying malfunction

codes. These error codes can be seen on the main screen of the

LGMV software program. For an overview of Water Mini error codes,

see page 79. For detailed information on how to troubleshoot indi-

vidual error codes, see the Water Mini Service Manual.

Figure 72: Error Code Screen.

Note:

Images on these pages are examples of LGMV screenshots. Actual images may differ depending on the version of the software and the units

installed.

• CPU: Pentium

IV 1.6 GHz

• Main Memory: 1G
• Operating System: Windows

XP/Vista/7 32 bit (recommended),

64 bit

• Hard Disk: 600 MB when operating
• MS Office 2003, 2007 (recommended) for select reporting

functions

Summary of Contents for ARWN038GA2





























































































Search results

Summary of Contents for ARWN038GA2

Reviews:

LG ARWN038GA2, Installation Operation & Maintenance, Page: 78 / 92

Search results

Summary of Contents for ARWN038GA2

Reviews: