manualshive.com logo in svg

LG ARWN038GA2, Installation Operation & Maintenance, Page: 18 / 92

Share
Download
LG ARWN038GA2 Installation Operation & Maintenance Download Page 18

18

MUL

TI V W

ater Mini System Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.  

©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG” is a registered trademark of LG Corp.

INSTALLATION

Transporting / Lifting the Water Source Unit

Transporting / Lifting

• When lifting the unit, use lifting straps and place around the unit as shown below. 
• Always lift the unit using properly sized lifting straps rated to carry the unit weight.
• Ensure the straps are long enough to maintain a maximum of a 40° angle as shown at “A”.

Caution when using forklift to transport an unpackaged unit. Consider the unit’s center of gravity when lifting. Protect the painted surfaces as 

necessary to prevent damage to the unit finish.

≤40° 

Mounting Rail

A:

B:

A

A

• 

One person should not carry the product.

• 

Some products include polypropylene bands around the unit for packaging. Do not use polypropylene bands to lift the unit. 

• 

Tear apart and throw away plastic packaging bags so that children may not play with them and risk suffocation and death.

• 

Lift the water source unit from the base at specified locations. Support the water source unit at a minimum of six (6) points to avoid 

slippage from the rigging apparatus. 

• 

Do not drop the unit when carrying it with a forklift.

• 

Use a minimum of three (3) lifting straps.

• 

Place a protective cloth or other soft material at the locations where the casing comes in contact with the lifting straps to prevent 

damage to painted surfaces.

• 

Always know where the center of gravity of the water source unit is before lifting.  Hoist the unit with the center of gravity centered 

among the lifting straps.

Figure 6: Transporting the Water Source Unit.

Capacity 

(ton)

 Net Weight 

(lbs.)

Shipping 

Weight (lbs.)

3.0

168

181

4.0

168

181

4.5

168

181

Table 6: Water Mini Net and Shipping Weights. 

Summary of Contents for ARWN038GA2





























































































Reviews:

No comments