LG A2UW18GFA0 Svc Manual Download Page 15

Page: 15 / 113

- 14 -

LGE Internal Use Only

Part 2 Functions & Controls

2. Air flow

2.1 Auto swing (left & right)

Right

Left

110

~ 120

Open

110

~ 120

Mode2

Mode3

Mode4

Mode5

Mode6

Mode7

Mode8

Mode9

OPEN

CLOSED

7~8

110~120

• By the horizontal airflow direction control key input, the left/right louver automatically operates with the auto swing or it

is fixed to the desired direction.

2.2 Auto swing (up & down)

• By the auto swing key input, the upper/lower vane automatically operates with the auto swing or it is fixed to the

desired direction.

2.3 Chaos swing (up/down)

• By the Chaos swing key input, the upper/lower vane automatically operates with the chaos swing or it is fixed to the

desired direction.

NOTE

: Some Models are different by swing width and swing pattern.

Summary of Contents for A2UW18GFA0


















































































































Search results

Summary of Contents for A2UW18GFA0

Reviews:

Related manuals for A2UW18GFA0

Brands by name

Popular brands

LG A2UW18GFA0, Svc Manual

Search results

Summary of Contents for A2UW18GFA0

Reviews:

Related manuals for A2UW18GFA0

Brands by name

Popular brands