Lexicon NuVerb Manual Download Page 75

Page: 75 / 125

NuVerb

User Guide

Reference

The Fader/MIDI Control Dialog

A dialog box is available from the Program Editor Fader/MIDI Cntl button which allows you
to configure the Hot Faders.

In the Program Editor, click on the
Fader/MIDI Cntl button to open the
dialog

Select a parameter to control...

Click on a parameter box to
pop up a parameter menu.

Radio buttons allow you to specify
the type of parameters which will
appear in the pop-up menu.

The parameter you selected
is displayed here.

The parameter type you selected
(Program, Effect, etc.) is displayed
here.

Allow selection of minimum
and maximum values for the
controller.

Displays the current
parameter value.

Allow selection of a specific
range (minimum to maximum)
to be assigned to the control-
ler.

Once you've selected a parameter, a set of assignment options will appear.

Allows selection of Hot Palette faders 1-5,
or any MIDI controller to be selected.

Allows selection of MIDI Channel
assigned to controller.

Summary of Contents for NuVerb






























































































































Search results

Summary of Contents for NuVerb

Reviews:

Related manuals for NuVerb

Brands by name

Popular brands

Lexicon NuVerb, Manual

Search results

Summary of Contents for NuVerb

Reviews:

Related manuals for NuVerb

Brands by name

Popular brands