Lexicon NuVerb Manual Download Page 120

Page: 120 / 125

Lexicon

Appendix

A-2

Hardware Troubleshooting

If you do not get audio output, perform the following checkout procedure.

1. Recheck the cables and the audio connections of the entire signal chain. Verifying that the

individual parts of the chain work independently is often helpful.

2. Remove the board, observing all installation precautions in regard to static, power down

etc. Check for bent pins on the edge connector. If the pins are bent, contact Lexicon

Customer Service at (617) 736-0300.

3. If the connector pins are OK, reinstall. Carefully seat the board, re-boot the Mac and retry

the audio pass-through test.

4. If you are using the Digidesign Expansion chassis, use the “Expansion View™” applica-

tion to verify that the card is being recognized by the Expansion chassis as well as the Mac.

5. Proceed to software installation to enable futher testing.

Software Verification

Check off these items:

■

Compressed application file copied to hard drive and decompressed

■

MIDI Manager placed in System Extensions folder

■

MIDI Manager Patchbay placed in the Apple Menu Items folder

■

Apple MIDI Driver placed in the System folder (not “nested” in another folder within the

System folder)

■

Double click on the NuVerb application icon to open; select

Create Default Library

from

the

Options

■

Start your audio source and verify NuVerb is producing reverb

Summary of Contents for NuVerb






























































































































Search results

Summary of Contents for NuVerb

Reviews:

Related manuals for NuVerb

Brands by name

Popular brands

Lexicon NuVerb, Manual

Search results

Summary of Contents for NuVerb

Reviews:

Related manuals for NuVerb

Brands by name

Popular brands