LevelOne ProCon GSW-1291 User Manual Download Page 8

Page: 8 / 234

User Manual

Publication date: May, 2005

Revision A1

1-2. Checklist

Before you start installing the switch, verify that the package contains the

following:



One set of GSW-1291



Mounting Accessory (for 19” Rack Shelf)



This User's Manual



AC Power Cord



RS-232 Cable

Please notify your sales representative immediately if any of the aforementioned
items is missing or damaged.

1-3. Features

GSW-1291 is a standalone off-the-shelf switch which provides the

comprehensive features listed below for users to perform system network
administration and efficiently and securely serve your network.

•

Hardware

•

10 10/100/1000Mbps Auto-negotiation Gigabit Ethernet TP ports

•

2 10/100/1000Mbps TP or 1000Mbps SFP Fiber dual media auto sense

•

208KB on-chip frame buffer

•

Jumbo frame support

•

Programmable classifier for QoS (Layer 4/Multimedia)

•

8K MAC address and 4K VLAN support (IEEE802.1Q)

•

Per-port shaping, policing, and Broadcast Storm Control

•

IEEE802.1Q-in-Q nested VLAN support

•

Full-duplex flow control (IEEE802.3x) and half-duplex backpressure

•

Extensive front-panel diagnostic LEDs; System: Power, TP Port1-12: LINK/ACT,

10/100/1000Mbps, SFP Port 11, 12: SFP(LINK/ACT)

•

12 port IEEE802.3af PSE

•

Endpoint with 48VDC power through RJ-45 pin 1, 2, 3, 6

•

Powered Device(PD) auto detection and classification

•

PoE-PSE status and activity LED indicator

•

Overcurrent and overtemperature fault management with LED indicator

•

Smart feature for PD on/off, class, feeding priority

Summary of Contents for ProCon GSW-1291











































































































































































































































Search results

Summary of Contents for ProCon GSW-1291

Reviews:

Related manuals for ProCon GSW-1291

Brands by name

Popular brands

LevelOne ProCon GSW-1291, User Manual

Search results

Summary of Contents for ProCon GSW-1291

Reviews:

Related manuals for ProCon GSW-1291

Brands by name

Popular brands