Lenovo ThinkPad S5 2nd Generation Hardware Maintenance Manual Download Page 86

Page: 86 / 110

Step

Screw (quantity)

Color

Torque

M2 × 4 mm, flat-head, nylon-coated (1)

Black

0.196 Nm
(2 kgf-cm)

When you install the thermal fan assembly:

• Do not touch the thermal grease.

• Do not press, touch, or rotate the fan impeller.

• Do not touch the fan inlet hole.

• Do not twist or pull the cable of the thermal fan assembly.

• Do not apply pressure on the top and bottom covers of the thermal fan assembly.

• Do not press the heat pipe. Hold both sides of the heat pipe if you need to take the thermal fan assembly.

• Do not shake or drop the thermal fan assembly.

• Ensure that the fan connector is attached firmly.

• Ensure that the base cover assembly is attached firmly; otherwise, battery connection may fail.

• Always wear fingerstalls when handling the thermal fan assembly. Do not touch or hold any part of the

thermal fan assembly with bare fingers.

• Before you attach the thermal fan assembly to the computer, apply thermal grease, at an amount of 0.2

grams, on the part marked

as shown in the following illustrations. Either too much or too less

application of grease can cause a thermal problem due to imperfect contact with a component. You
should peel the thin film off from the rubbers marked

Hardware Maintenance Manual

Summary of Contents for ThinkPad S5 2nd Generation















































































































Search results

Summary of Contents for ThinkPad S5 2nd Generation

Reviews:

Related manuals for ThinkPad S5 2nd Generation

Brands by name

Popular brands

Lenovo ThinkPad S5 2nd Generation, Hardware Maintenance Manual

Search results

Summary of Contents for ThinkPad S5 2nd Generation

Reviews:

Related manuals for ThinkPad S5 2nd Generation

Brands by name

Popular brands