Lenovo M93/p Tiny User Manual Download Page 85

Page: 85 / 158

What to do next:

• To work with another piece of hardware, go to the appropriate section.

• To complete the installation or replacement, go to “Completing the parts replacement” on page 80.

Replacing the system fan

Attention:

Do not open your computer or attempt any repair before reading and understanding the “Important safety information”
on page v.

This section provides instructions on how to replace the system fan.

CAUTION:
Hazardous moving parts. Keep fingers and other body parts away.

To replace the system fan, do the following:

1. Turn off the computer and disconnect all power cords from electrical outlets.

2. Remove the computer cover. See “Removing the computer cover” on page 55.

3. Locate the system fan in the computer. See “Locating components” on page 11.

4. Disconnect the system fan cable from the system board.

Chapter 5

Installing or replacing hardware

Summary of Contents for M93/p Tiny































































































































































Search results

Summary of Contents for M93/p Tiny

Reviews:

Related manuals for M93/p Tiny

Brands by name

Popular brands

Lenovo M93/p Tiny, User Manual

Search results

Summary of Contents for M93/p Tiny

Reviews:

Related manuals for M93/p Tiny

Brands by name

Popular brands