Lenovo M93/p Tiny User Manual Download Page 70

Page: 70 / 158

5. Remove the two screws that secure the hard disk drive assembly. Slide the hard disk drive assembly as

shown, and then lift the hard disk drive assembly to remove it from the chassis.

Figure 40. Removing the hard disk drive assembly

To install the hard disk drive assembly, do the following:

1. Position the hard disk drive assembly on the system board so that the two holes in the hard disk drive

bracket are aligned with the standoffs on the system board. Slide the hard disk drive assembly as shown
until the two screw holes

are aligned with the corresponding screw posts on the system board.

Figure 41. Installing the hard disk drive assembly

ThinkCentre M93/p Tiny User Guide

Summary of Contents for M93/p Tiny































































































































































Search results

Summary of Contents for M93/p Tiny

Reviews:

Related manuals for M93/p Tiny

Brands by name

Popular brands

Lenovo M93/p Tiny, User Manual

Search results

Summary of Contents for M93/p Tiny

Reviews:

Related manuals for M93/p Tiny

Brands by name

Popular brands