Lenovo IdeaPad S200 Hardware Maintenance Manual Download

Page: 112 / 138

7. Peel off the paper that protects the stickers on the new Wi-Fi antenna.

Figure 48. Peeling off the paper that protects the stickers

8. Stick the Wi-Fi antenna to the chassis as shown. Then insert the Wi-Fi antenna cable through the

hole in the chassis.

Figure 49. Installing the Wi-Fi antenna and cable

Note:

Refer to the left picture for the front Wi-Fi antenna and the right picture for the rear Wi-Fi antenna.

9. Connect the antenna cable to the Wi-Fi card.

10. Depending on whether you are replacing the front Wi-Fi antenna or the rear Wi-fi antenna, do one

of the following:

• If you are replacing the front Wi-Fi antenna, reinstall the front bezel. See “Replacing the front bezel”

on page 83.

106

Lenovo S200 Hardware Maintenance Manual

Summary of Contents for IdeaPad S200











































































































































Search results

Summary of Contents for IdeaPad S200

Reviews:

Related manuals for IdeaPad S200

Brands by name

Popular brands

Lenovo IdeaPad S200, Hardware Maintenance Manual

Search results

Summary of Contents for IdeaPad S200

Reviews:

Related manuals for IdeaPad S200

Brands by name

Popular brands