Leguan L190 Operator'S And Service Manual Download Page 19 | Manualshive

Page: 19 / 53

background image

19

_________________________________________________________________________________

4.3 Wireless remote control (option)

This access platform can be equipped with wireless remote control. The remote can be used to
operate outriggers and drive functions. The remote, spare battery and a battery charger are located
underneath the pedestal valve box.

Figure 7: Remote storage

1.  Remote
2.  Spare battery
3.  Battery charger

Protect the remote from snow and ice. If lower controls is not selected, keep the remote in the storage
enclosure. The minimum temperature for the remote storage and use is -20 °C, store the remote
indoors if necessary.

Figure 8: Wireless remote

1. Emergency stop button (The remote emergency stop will only operate when the remote

control use is selected.)

2.  Automatic levelling switch
3.  Start button for remote
4.  Drive speed selector
5.  Outrigger control levers, left side
6.  Outrigger control levers, right side
7.  Electric motor start/stop switch
8.  Combustion engine start/stop switch
9.  Levers for driving

2

3

1

«
...
17
18
19
20
21
...
»

Summary of Contents for L190






















































Reviews:

No comments

Related manuals for L190

Brand: Paradyne Pages: 112

Brand: Cambium Networks Pages: 215

Brand: RAK Pages: 30

Brand: MICROENER Pages: 24

ISDN SOHO Router

Brand: AOpen Pages: 89

Brand: National Instruments Pages: 80

Brand: Advantech Pages: 108

Brand: ZALMAN Pages: 16

Mustang-M2AE-MX1

Brand: IEI Technology Pages: 58

24-Port 1000BASE-T

Brand: Comet Labs Pages: 44

Brand: Fluke Pages: 102

Brand: Allied Telesis Pages: 2

Brand: Kentrox Pages: 246

LinkStation 500

Brand: Buffalo Pages: 139

Brand: Steren Pages: 130

HHM Series HHM1521

Brand: TDK Pages: 2

Brand: B&B Electronics Pages: 74

Brand: ORANGE Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands