Lectronix T8510 User Operating Instructions Manual Download Page 14 | Manualshive

Page: 14 / 43

background image

9

Camera

The VIS supports one NTSC camera. An optional camera can be connected to the VIS. The camera is
connected to the Fleet Management/Camera connector shown in the VIS Connector Definitions section.

Contact Lectronix at the customer support number for Camera information. See Appendix A.

«
...
12
13
14
15
16
...
»

Summary of Contents for T8510












































Reviews:

No comments

Related manuals for T8510

Maestro 3250 - Automotive GPS Receiver

Brand: Magellan Pages: 77

Brand: Gigabyte Pages: 40

MEDIA-NAV EVOLUTION

Brand: Renault Pages: 298

Brand: Boss Audio Systems Pages: 19

Brand: FOUR Pages: 28

Brand: Kraken Acoustics Pages: 12

Brand: Digital Flash Memory Pages: 10

Brand: Steren Pages: 31

Brand: Panasonic Pages: 100

OPTISOUND OPTIFORD6-V8

Brand: Vibe Pages: 4

Brand: Hitachi Pages: 228

Brand: Philips Pages: 16

Brand: Philips Pages: 76

Brand: Philips Pages: 94

Brand: Samsung Pages: 16

Brand: Samsung Pages: 19

Brand: Samsung Pages: 19

Brand: Samsung Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands