background image

Active   (on)   when   a   link   fault   between   the   computer   and   the   system   occurs.   Restart   the   fault
condition. If the problem persists, see section  7.1 for resolution. Amber color.

(f) POWER: "POWER" 

Active (on) when a fault in the system occurs. It may be due to a fault in the main power

supply, or emergency power supply. Restart the fault condition. If the problem persists, see section
7.3 for resolution. Amber color.

(g) EMIC: "EMERGENCY MICROPHONE"

Active (on) when a fault in the emergency microphone occurs. Restart the fault condition. If the
problem persists, see section 7.5 for resolution. Amber color.

 2.1.3  EMERGENCY ALERT SOURCE INDICATORS

Emergency   alert   sources   indicators   indicate   the   operating   condition   of   the   pre-recorded

messages of the system and the emergency microphone.

(h) EVAC: "EVACUATION" 

Active (on) when the message that is being issued is intended for the evacuation of the

voice alarm zone or zones selected. Red color.

(i) ALERT: "ALERT" 

Active (on) when the message that is being issued is intended for the alert of the voice

alarm zone or zones selected. Amber color.

(j) EMIC: "EMERGENCY MICROPHONE" 

Active (on) when the microphone is available to issue an evacuation message in the zone

or zones selected. If the indicator is off, wait for it to turn on, a warning signal might be sounding.
Amber color.

 2.1.4  SELECTION INDICATORS

Zone extensions for the Voice Alarm Panel feature zone memory selection indicators. When

selected by pressing the corresponding key, the indicator next to it activates (on). Green color.

LDA Audio Tech - Severo Ochoa, 31- 29590 MALAGA, SPAIN. Tel: +34 952028805 

www.lda-audiotech.com/en

3

User’s Manual: VAP 1

Summary of Contents for LDAVAP1





























Reviews: