LAUREL LAUREATE 2 Series Owner'S Manual Download Page 40

Page: 40 / 64

- 40 -

KEYSTROKES FOR SETPOINT SETUP

If the

MENU

key does not work, see Section 9 “Enabling & Locking Out Menu Items.”

Press Menu
Select Key

Press Digit
Select Key

Press Value Select
Key

ALSEt

Alarm Setup for
relays 1 & 2 if
detected.

Press

until

ALSEt

is displayed.

0000

Relay open or closed
when in alarm state.

AL1 relay closed

AL2 relay closed

AL1 relay open

AL2 relay closed

AL1 relay closed

AL2 relay open

AL1 relay open

AL2 relay open

000

Alarm latching or non-
latching (auto reset).
See Glossary.

AL1 non-latching

AL2 non-latching

AL1 latching

AL2 non-latching

AL1 non-latching

AL2 latching

AL1 latching

AL2 latching

Alarm state occurs at

or above setpoint, or
below setpoint, or is
disabled. Front panel
indicator lights come
on in alarm state,

AL1 at or above

AL2 at or above

AL1 below

AL2 at or above

AL1 disabled

AL2 at or above

AL1 at or above

AL2 below

AL1 below

AL2 below

AL1 disabled

AL2 below

AL1 at or above

AL2 disabled

AL1 below

AL2 disabled

AL1 disabled

AL2 disabled

000

Hysteresis mode or
band deviation mode.
See Glossary.

AL1 band deviation AL2 band deviation

AL1 split hysteresis AL2 band deviation

AL1 band deviation AL2 split hysteresis

AL1 split hysteresis AL2 split hysteresis

No deviation or hysteresis in menu.

AL1 span hysteresis AL2 band deviation

AL1 span hysteresis AL2 split hysteresis

AL1 span hysteresis AL2 span hysteresis

0000

Number of consecutive
readings in alarm zone
to enter alarm state.

After 1 reading

After 16 readings

After 2 readings

After 32 readings

After 4 readings

After 64 readings

After 8 readings

After 128 reading

ALS34

Alarm Setup for
relays 3 & 4 if
detected.

0000

Relay open or closed
when in alarm state.

AL3 relay closed

AL4 relay closed

AL3 relay open

AL4 relay closed

AL3 relay closed

AL4 relay open

AL3 relay open

AL4 relay open

000

Alarm latching or non-
latching (auto reset).

AL3 non-latching

AL4 non-latching

AL3 latching

AL4 non-latching

AL3 non-latching

AL4 latching

AL3 latching

AL4 latching

Summary of Contents for LAUREATE 2 Series

































































Search results

Summary of Contents for LAUREATE 2 Series

Reviews:

Related manuals for LAUREATE 2 Series

Brands by name

Popular brands

LAUREL LAUREATE 2 Series, Owner'S Manual

Search results

Summary of Contents for LAUREATE 2 Series

Reviews:

Related manuals for LAUREATE 2 Series

Brands by name

Popular brands