LAUREL LAUREATE 2 Series Owner'S Manual Download Page 12

Page: 12 / 64

- 12 -

9. ENABLING & LOCKING OUT MENU ITEMS

For security reasons and ease of meter operation, any or all menu
items can be disabled or "locked out" so that they are no longer
accessible from the front panel. Each function to be disabled can
be set to "1" under menu headers

Loc 1-3

, while each function to

be enabled can be set to "0."

Access to the menu headers

Loc 1-3

can be disabled by installing

a hardware jumper

“

” on the power supply board. With the jumper

installed, the operator no longer has access to the menu headers

Loc 1

. He can no longer enable or disable menu items, but he

still has access to previously enabled menu items. With the jumper
removed, the operator has access to menu headers

Loc 1

and

can enable or disable menu items.

SETTING HARDWARE LOCKOUT JUMPER

To access the lockout jumper, remove the rear panel per Section
9 and locate jumper

“a”

in the lower portion of the power supply

board next to the input connectors (see figure at right).

Check lockout status.

Many Laurel meters are shipped with lockouts in place.

This causes menu items described later in this manual not to appear.

SETTING SOFTWARE LOCKOUTS

To set up a meter, it may be necessary to enable
menu items by setting lockout digits to

“0”. Following

setup, reset the digits to "1" if you do not want the
menu item to be changed by an operator.

Loc 1 Loc 2 Loc 3

Press the

MENU

key until

Loc 1, Loc 2

Loc 3

displayed, as desired.

Note:

hardware lockout jumper

“a”

must be removed (see above).

11111

Press to display the lockout status, con

sisting of 1’s

and 0’s. The left digit will flash. Press again to step
to the next digit, which will flash.

00000

12345

Press

to set the flashing digit to "0" to enable the

menu item or to "1" to disable. Press

MENU

to enter.

See the table to the right for list of menu items that
can be enabled or disabled.

Enabled or Disabled
Menu Items

Loc 1

- Input type selection.

- Meter setup, configuration

& decimal point

- Filter selection.

- Scale or Lo, Hi input.

- Offset or Lo, Hi reading

Loc 2

- Alarm setup

- Alarm setpoint value

programming.

- Analog output scaling.

- Serial interface setup.

Loc 3

- View peak or tare value

- View alarm setpoints

- Reset (peak & latched alarms)

- Reset (meter reset)

Summary of Contents for LAUREATE 2 Series

































































Search results

Summary of Contents for LAUREATE 2 Series

Reviews:

Related manuals for LAUREATE 2 Series

Brands by name

Popular brands

LAUREL LAUREATE 2 Series, Owner'S Manual

Search results

Summary of Contents for LAUREATE 2 Series

Reviews:

Related manuals for LAUREATE 2 Series

Brands by name

Popular brands