background image

LAUNCH

 

 

                                                

               TLT632AF INSTALLATION MANUAL 

 

                                                  2 

1 Precautions

 

 

 
 
 
 
 

 
 

  

    Warnings

 

 

Please read and understand the manual before 
operation 

 

This manual is an important part of the product.  
Please read and understand it thoroughly. 

 

Keep the manual for future use in inspection and 
maintenance. 

 

Do not use the product for any other purposes. 

 

The manufacturer is not responsible for any damage 
caused by improper use or uses other than the 
designed purpose. 

 
 
 
 
 

 

 

 

 

 

 

 

 

 

Precautions for Installation and 

Adjustment

 

 

Please read this manual and operation manual in full 
before installation and adjustment.    Any changes to 
the components or use for other purpose without the 
consent of the manufacturer may lead to direct or 
indirect damage to the product. 

 

Installation and adjustment personnel should have an 
understanding of electronic equipment. 

 

Never allow untrained personnel to operate the lift. 

 

Allow sufficient space for the lift so that operation 
should not be hindered. 

 

Do not install the lift in an environment with extreme 
temperature and humidity conditions.    Keep it away 
from heating device, faucet, humidifier or furnace. 

 

Do not install the lift outdoors or expose it to rain.    If 
it is really necessary to do so, a special order should 
be made from the manufacturer. 

 

Check the components against parts list before 
installation.  In case of any  questions, please 
contact your dealer or Launch Tech. 

 

For the sake of technical improvements, Launch 
(Shanghai) Machinery Co., Ltd reserves the right to 
change the specifications without prior notice. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for TLT632AF
















Reviews: