Lattice Semiconductor CertusPro-NX Usage Manual Download Page 39 | Manualshive

Page: 39 / 171

background image

CertusPro-NX SerDes/PCS Usage Guide

Preliminary

Technical Note

FPGA-TN-02245-0.81

© 2020-2021 Lattice Semiconductor

39

All rights reserved. CONFIDENTIAL

Port Name

I/O

Width

Description
the PMA control logic which now controls the PMA hard macro.
The PMA hard macro is thus disconnected from the PMA
control logic:
This signal is used for two purposes:

Select the multiplexer between ACJTAG controller and
functional logic at the PMA interface directly.

Put out of reset the ACJTAG controller.

This signal is used as reset input for the embedded ACJTAG
controller of the PMA.

acjtag_enable_i

In

1

This signal configures the PMA in ACTAG test mode. By default,
it resets the Tx and Rx driver and receiver followed by loading
the driver and receiver with default settings. The PMA receiver
is by default in DC test mode and the transmitter is driving 0.

acjtag_acmode_i

In

1

When acjtag_enable_i == 1’b1, this signal selects either AC
mode (1’b1) or DC mode (1’b0).

acjtag_drive1_i

In

1

When acjtag_enable_i == 1’b1, this signal selects the differential
value the transmitter drives.

acjtag_highz_i

In

1

When acjtag_mode_i == 1’b1, assertion of this signal puts the
PMA driver in high impedance.

acjtagpout_i

In

1

ACJTAG Output Data.

acjtagnout_i

In

1

ACJTAG Output Data.

Note:

For multiple ports, [n] indicates lane/channel number.

Data Bus Sharing and Mapping

defines the detailed usage for different bits of MPCS/EPCS data bus.

Table 5.12. Data Bus Sharing and Mapping

MPCS Module Port

MPCS Mode
Protocol != “10GE”

MPCS Mode
Protocol == “10GE”

EPCS Mode

Tx Path
mpcs_tx_ch_din_i[39:0]/
epcs_txdata_i[39:0]

tx_data[39:0]
4-byte output data

bit[39:30]: byte_3

bit[39]: cordisp bit or data
bit[9] when being used in 10b
mode.

bit[38]: control character when
being used in 8B/10B mode; or
data bit[8] when being used in
10b mode.

bit[37:30]: data bit[7:0]

bit[29:20]: byte_2

bit[19:10]: byte_1

bit[9:0]: byte_0

tx_data_64b[39:0]
Input data.

40-bit input data.

mpcs_tx_ch_din_i[43:40]/
epcs_txdata_i[43:40]

tx_frcdisp[3:0]

1: use “force running disparity”
mode; in this mode, the running
disparity is indicated by
“tx_dispval” signal.

0: do not use “force running
disparity” mode.

tx_data_64b[43:40]
Input data.

—

mpcs_tx_ch_din_i[47:44]/
epcs_txdata_i[47:44]

tx_dispval[3:0]
In “force running disparity” mode,

tx_data_64b[47:44]
Input data.

—

«
...
37
38
39
40
41
...
»

Summary of Contents for CertusPro-NX












































































































































































Reviews:

No comments

Related manuals for CertusPro-NX

Brand: 3Com Pages: 2

Brand: 3Com Pages: 74

Brand: 3Com Pages: 6

Brand: Measurement Computing Pages: 27

NVIP- NVRA0104/GO

Brand: Novus Pages: 44

Brand: Buffalo Pages: 2

iTRON B 70.2040

Brand: JUMO Pages: 41

EK-Quantum Momentum ROG Rampage VI Encore

Brand: EK Pages: 11

Brand: ZoneVu Pages: 15

Brand: FUNcube Pages: 23

Brand: VCS Pages: 118

Brand: Observint Pages: 117

zoomno MSC-5578

Brand: BIIZZY Pages: 2

Brand: XtendLan Pages: 21

Brand: Ariesys Pages: 10

Brand: Laser Pages: 4

XC-16CH-NVR-4TB

Brand: Xyclop Pages: 19

Brand: Patton electronics Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands