Lattice Semiconductor CertusPro-NX Usage Manual Download Page 15

Page: 15 / 171

CertusPro-NX SerDes/PCS Usage Guide

Preliminary

Technical Note

FPGA-TN-02245-0.81

Features



Single Channel MPCS Functionalities

From 625 Mb/s up to 10.3125 Gb/s per channel

Word alignment and link synchronization FSM

Supports DisplayPort, SLVS-EC, CoaXPress, and Ethernet 1000BASE-X/SGMII/XAUI/QSGMII protocols

Supports popular 8B/10B PCS-based protocols

Supports user-specified generic 8B/10B mode

Supports Ethernet 64B/66B coding and decoding

Supports per channel configuration

PMA-only mode allows direct 8-bit or 10-bit interface to FPGA logic



Multiple Channel Alignment

Up to eight channels of the same protocol

Minimized Transmitter (Tx) lane-to-lane skew

Receiver (Rx) multiple lane de-skew (up to 100UI)



Multiple Protocol Clock Tolerance Compensation (CTC) logic

Compensates for frequency difference between reference clock and received data rate

Allows user-defined SKIP pattern of 1, 2, or 4 bytes in length



Integrated Loopback Modes for System Debugging

Two loopback modes are provided by SerDes (PMA)

Two loopback modes are provided by MPCS 8B/10B mode

Three loopback modes are provided by MPCS 64B/66B mode



Rx Eye Monitor

Integrated 2D eye-scan for each Rx channel

First on-chip SerDes debug tool in Lattice general purpose FPGAs



SerDes Power Supply Monitor

Integrated real-time monitor for SerDes power supply



Easy-to-Use Design Interface in Lattice Radiant

Design Tool

Easy-to-use Graphic User Interface (GUI)

Some easy-to-use soft IP cores and example projects available

Summary of Contents for CertusPro-NX












































































































































































Search results

Summary of Contents for CertusPro-NX

Reviews:

Related manuals for CertusPro-NX

Brands by name

Popular brands

Lattice Semiconductor CertusPro-NX, Usage Manual

Search results

Summary of Contents for CertusPro-NX

Reviews:

Related manuals for CertusPro-NX

Brands by name

Popular brands