Laser Technology TruSense S300 Series User Manual Download Page 36 | Manualshive

Page: 36 / 91

background image

LTI TruSense S300 Series Integration Manual 3nd Edition

Page 30

Copyright © [2016] Laser Technology, Inc. All Rights Reserved. Unauthorized duplication, in whole or in part, is strictly prohibited.

10 Reference

Application Examples

These examples are not absolute - sensor setup configuration varies depending on ambient
conditions, target integrity, distance, constraints, and user requirements.

Liquid Measurement

To measure the material depth in the tank or vessel (the top of a liquid):

•

The sensor must be able to penetrate air-born fog or mist inside the vessel.
Choose Last Target for this.

•

Set the unit to begin measuring upon power up - enable AutoStart. AutoStart
will allow sensor to automatically re-start after a power re-start. See $MA

command.

•

Each type of liquid surface conditions may react differently, and the user will
need to adjust the settings for optimum performance. See $OS command.

•

Measuring liquid in an agitated state might achieve more accurate results if a
stilling well or a by-pass pipe is used, as shown below.

Figure 6: Tank and Vessel Liquid

«
...
34
35
36
37
38
...
»

Summary of Contents for TruSense S300 Series




























































































Reviews:

No comments

Related manuals for TruSense S300 Series

Brand: D-Link Pages: 2

Brand: Harol Pages: 16

Brand: aci Pages: 8

BACnet / Modbus IMMERSION Series

Brand: aci Pages: 8

Brand: aci Pages: 4

Brand: Coby Pages: 16

Brand: Memphis Shades Pages: 2

Brand: Peg-Perego Pages: 16

ALK.00.733.15000/B

Brand: SW-Motech Pages: 14

Brand: Ednet Pages: 7

Brand: Toro Pages: 8

Brand: Gator Pages: 8

Brand: Zooka Sports Pages: 32

STEADYSTAND Cross Basic

Brand: ACEBIKES Pages: 6

Brand: RADARchron Pages: 2

Brand: Ednet Pages: 4

Brand: Aerotech Pages: 58

Brand: Oncam Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands