Laser Technology TruSense S300 Series User Manual Download Page 17

Page: 17 / 91

LTI TruSense S300 Series Integration Manual 3rd Edition

Page 11

Figure 5: Vessel 4-20 Setup

7 4-20mA Work Sheet

The following Work Sheet can be printed out and used to build ASCII serial command and

record the sensor settings for future reference. The intent of this worksheet is to allow the

user to build each ASCII serial command for the 4-20mA loop.

Note:

An alternative programing method is available for setting up the sensor. The LTI

TruSense S330 programing interface software tool (See Appendix B). Using this tool for

setting up the sensor in an application requires no prior knowledge of the RS-232 ASCII

commands. The tool will send the appropriate commands necessary to configure the

sensor to integrate to your application environment.

Summary of Contents for TruSense S300 Series



























































































Search results

Summary of Contents for TruSense S300 Series

Reviews:

Related manuals for TruSense S300 Series

Brands by name

Popular brands

Laser Technology TruSense S300 Series, User Manual

Search results

Summary of Contents for TruSense S300 Series

Reviews:

Related manuals for TruSense S300 Series

Brands by name

Popular brands