background image

p/n 2M-W2029  OpM  L

VC- V

entless Universal Hood

6

INSTALLATION (continued)

UNDER-HOOD APPLIANCE LIMITATIONS:

1. 

Appliance must be installed per manufactures instructions.

2. 

Electrical appliances only. Not Intended for gas fired units.

3. 

All appliances under the hood must be connected to the hood appliance interlock circuit.

4. 

All appliances must meet the requirements outlined in the cooking appliance limitations chart below.

EQUIPMENT PARAMERTUER - LVC-46 (X)

Parameters Appliance 

Type

Max Cooking 

Temp

Max Single Units 

Cooking Area

Dim “A” (1) 

Min.

Dim “A” (2) 

Min.

Dim “B” (3) 

Min.

Dim “C” (4) 

Min.

Dim “D” (5) 

Min.

Convection Oven

550°F (287°C)

19 Cubic Feet

1”

6”

3”

0”

8”

Double Stack Oven
Steamer/Combi Oven
Bakery Oven / Proofer

Intended for installation in accordance with:

The standard for ventilation control and fire 

protection of commercial cooking operations 

NFPA 96, the National Electric Code NFPA 70 

and local codes where applicable.
Only electrically heated appliances are 

acceptable for installation.  Appliance Operation 

Requires the Fire suppression system be setup, 

charged and certified by an authorized ANSUL® 

distributor.  The airflow monitoring system 

will prevent appliance operation if insufficient 

airflow is detected or all filters are not in place.  

The service panel must be in place for blower 

operation.

1. Dim “A” minimum distance from the lower edge of the hood skirt and the top of the appliance.
2. Dim “A” maximum distance from the lower edge of the hood skirt and the top of the appliance.
3. Dim “B” minimum overhang between the hood side skirt and the appliance side.
4. Dim “C” minimum space between the hood rear skirt and the back panel of the appliance.
5. Dim “D” minimum overhang between the front lower edge of the hood to the oven’s heated surface.

IL2871

52.20”

45.82”

SIDE VIEW

FRONT VIEW

D

B

A

C

Summary of Contents for LVC-46

































Reviews: