![background image](http://html1.mh-extra.com/html/landmann/470430/470430_assembly-and-operating-instructions-manual_673774016.webp)
PAGE
Pellet Grill
16
Preparation for Use & Lighting Instructions
Step 6
Ensure the contorl knob is in the OFF position.
Step 7
Turn the control knob to “High”.
Step 8
Observe the auger turning as pellets fill the tube. Once pellets reach the fire pot, turn OFF the grill. DO NOT reach into the
fire pot.
Step 9
Re-install the flame tamer, grease tray, cooking grates and warming racks. Close the grill lid. The grill is now ready for use.
Follow the LIGHTING INSTRUCTIONS to continue.
LIGHTING INSTRUCTIONS
1. With the grill properly setup and located for operation, ensure control knob is in the OFF position. Plug the power cord
into a 120V grounded electrical outlet. (Refer to SETUP PROCEDURE for more information.)
2. Open the grill lid. Ensure all components are properly installed and ready for use.
3. Ensure the hopper does not contain any foreign objects and is properly filled with barbecue wood pellets.
4. Ensure the auger tube of the hopper is filled with pellets, if not, go back to Setup Procedure to fill pellets into auger tube.
5. Turn the control knob to ‘Smoke’. Listen for operation of fan and auger motors. Within 5 minutes smoke should become
visible. If smoke does not initially appear, turn OFF power and wait 5 minutes before attempting to relight. (Refer to the
troubleshooting section of the manual for more information.)
6. Ensure the grill is lit, keep the grill lid open for 5 minutes to complete the lighting procedure.
7. Select the desired cooking temperature and smoking preset. (Refer to COOKING INSTRUCTIONS for more operating infor-
mation.)
Note:
We recommend setting the control knob to “High” for 10 to 15 minutes to preheat the grill.
If the grill temperature is higher than your selected setting temperature, open grill lid to cool until the
grill temperature is close to the selected setting temperature.
WARNING:
• The pellet hopper must be properly setup with pellets in the auger tube prior to lighting the grill.
• Never add or use wood chips or particles in the hopper. Use only barbecue grade pellets.
• Use only a maximum length of 25’, extension cords with a 3 prong grounding plug rated for power of the equipment
and approved for outdoor use with a W-A marking.
• Do not break the ground end off the cord or use a non-grounded outlet or extension cord.
• Never immerse cord, plugs or electric elements in water or any liquid.
• Never operate the grill with a damaged power cord or plug, or after the grill has malfunctioned or been damaged in
any manner.
• Keep any power cord away from any heated surfaces.
NOTE: If the grill fails to light, inspect the fire pot for the presence of pellets or build-up of pellet
ash. If the fire pot contains too much ash, clean it out using a shop vacuum. Also be certain the
fan blower motor and auger are working by observing these parts after starting the grill. If they
are working, turn OFF the power and reassemble all components.
WARNING:
Never inspect or perform maintenance on a hot grill. Allow to properly
cool before inspecting or cleaning your grill.
Summary of Contents for 470430
