background image

4

How To Use This Manual

This manual contains the following sections:

How to Use This Manual

Safety

Operations

Maintenance

The HOW TO USE THIS MANUAL section will tell you 
how to find important information for ordering correct 
repair parts.

Parts may be ordered from authorized dealers. When 
placing an order for parts, the machine model and 
machine serial number are important. Refer to the 
MACHINE DATA box which is filled out during the 
installation of your machine. The MACHINE DATA box 
is located on the inside of the front cover of this manual. 

The model and serial number will be found on a decal 
attached to the machine.

The SAFETY section contains important information 
regarding hazardous or unsafe practices of the 
machine. Levels of hazards are identified that could 
result in product damage, personal injury, or severe 
injury resulting in death.

The OPERATIONS section is to familiarize the operator 
with the operation and function of the machine.

The MAINTENANCE section contains preventive main-
tenance to keep the machine and its components in 
good working condition. They are listed in this general 
order:

Maintenance & Service

Unloader Valves

Winterizing Procedure

High Limit Hot Water Thermostat

Pumps

Cleaning Of Coils

Rupture Disk

Fuel

Fuel Control System

Fuel Quality / Storage

Electrode Setting

Burner Nozzle

Landa Sure Fire Oil Burner

Coil Removal

Troubleshooting

NOTE: The manual part number is located on the 
lower right corner of the front cover.

Model:

Date of Purchase:

Serial Number:

Dealer:

Address:

Phone Number:

Sales Representative:

Landa PDHW Series Operator’s Manual  8.919-980.0 - B

Summary of Contents for PDHW5-35624E

























Reviews: