background image

10

Operations

Assembly

STEP 1:

 Attach a 5/8” water supply 

hose to inlet connector. Minimum 
flow should be 6 or 10 gpm 
depending on model of machine.

STEP 4:

 Check engine and pump 

oil level by removing oil dipstick, 
making sure oil is on proper 
indicator marking. Use SAE 10W-
30 or 15W-40 engine detergent oil 
for engine and SAE 10W-40 non-
foaming oil for pumps.

STEP 2:

 Attach wand to spray gun 

using teflon tape on threads to 
prevent leakage. Attach swivel 
connector on high pressure hose to 
spray gun using teflon tape on 
threads. Engage safety latch to 
prevent triggering gun when 
inserting high pressure nozzle.

STEP 5:

 Fill fuel tank with Ultra 

Low Sulfur Diesel fuel. 

STEP 3:

 Attach high pressure hose 

to discharge nipple using quick 
coupler. Lock coupler securely into 
place by pulling back coupler collar 
and inserting it into discharge 
nipple, then pushing collar forward 
to lock in place.

STEP 6:

 Install proper battery 

making sure that the red cable is 
attached to the positive terminal. 
Use a 12V Group 24 battery. 

Battery Installation

Due to Federal Regulations concerning shipment of 
corrosive chemicals, batteries are not shipped with this 
machine.

Local purchase of 
battery will be the 
responsibility of 
the owner. Auto-
motive type 12 
Volt Group 24 
battery is recommended for placement within the 
weather resistant box. Follow safety and installation 
instructions furnished with the battery.

Red cable is attached to battery (+) positive terminal, 
black cable is connected to battery (-) negative 
terminal.

Landa PDHW Series Operator’s Manual  8.919-980.0 - B

High Pressure 

Hose

Discharge 

Nipple

Quick 

Coupler

Diesel Fuel

SHIELD 
EYES

 

EXPLOSIVE 
GASES 

CAN CAUSE 

BLINDNESS OR INJURY

  

NO

SPARKS
FLAMES
SMOKING

SULFURIC 
ACID

CAN CAUSE 
BLINDNESS OR 
SEVERE BURNS

FLUSH EYES 
IMMEDIATELY 
WITH WATER 

GET 
MEDICAL 
HELP 
FAST

KEEP OUT OF THE REACH OF CHILDREN. DO NOT TIP. KEEP VENT CAPS TIGHT AND LEVEL.

D A N G E R / P O I S O N

Black - Negative 
Terminal

Red + Positive 
Terminal

Black

Red

High 

Pressure Hose

Spray 

Gun

Spray Wand

Safety 

Latch

Summary of Contents for PDHW5-35624E

























Reviews: