background image

17

Section 3: Options

9/18/14

SBL2566, SBL2574, & SBL2584 Snow Blowers   370-258M

Table of Contents

Deutsch HGD30 14 Pin Wiring
Harness

Refer to Figure 3-7:

Three 14 pin wiring harnesses are available. They attach
to the Snow Blower solenoids and skid steer 14 pin
coupler. 3 Cable ties are included with the wiring
harnesses. Pick the 14 pin wire harness that is designed
for your particular skid steer.

370-336A

Deutsch HGD30 14 Pin 2 Function

This harness will work with the following skid steers:

Bobcat with 14 pin coupler

GEHL with 14 pin coupler

Kubota with 14 pin coupler

Komatsu with 14 pin coupler

Mustang with 14 pin coupler

Takeuchi with 14 pin coupler

Volvo with 14 pin coupler

It will also work with the following skid steers by reversing
the red and green wires at the solenoid:

Case-Post 9/1/01 with 14 pin coupler

Case-400 Series with 14 pin coupler

New Holland with 14 pin coupler

370-337A

Deutsch HGD30 14 Pin 2 Function

This harness will work with the following:

John Deere with 14 pin coupler

370-338A

Deutsch HGD30 14 Pin 2 Function

This harness will work with the following:

John Deere “EH” with 14 pin coupler

Outer Skid Shoes

Refer to Figure 3-8:

Outer skid shoes are mounted on the outside of the side
panels and are adjustable by unbolting them and
reattaching them at a different height.

370-451K

SBL2566 SKID SHOE BUNDLE

370-438K

SBL2574 & SBL2584 SKID SHOE BUNDLE

Inner Skid Shoes

Refer to Figure 3-9:

Inner skid shoes are mounted behind the Snow Blower
and are adjustable vertically by pulling a bent pin and
moving the skid shoes up or down.

370-440K

SKID SHOE BUNDLE

Deutsch HGD30 14 Pin 2 Function Wiring Harness

Figure 3-7

Outer Skid Shoes

Figure 3-8

Inner Skid Shoes

Figure 3-9

35358

37221

37222

Summary of Contents for SBL2566







































Reviews: