background image

6

Introduction

SBL2566, SBL2574, & SBL2584 Snow Blowers   370-258M

9/18/14

Table of Contents

Owner Assistance

The Online Warranty Registration should be completed
by the dealer at the time of purchase. This information is
necessary to provide you with quality customer service.

The parts on your Snow Blower have been specially
designed by Land Pride and should only be replaced with
genuine Land Pride parts. Contact a Land Pride dealer if
customer service or repair parts are required. Your Land
Pride dealer has trained personnel, repair parts, and
equipment needed to service the implement.

Serial Number

Model No. _____________Serial No. _______________

For quick reference and prompt service, record model
number and serial number in the spaces provided above
and again on Warranty page 35. Always provide model
and serial number when ordering parts and in all
correspondences with your Land Pride dealer. Refer to
Figure 1 for location of your serial number plate.

Serial Number Plate Location

Figure 1

Further Assistance

Your dealer wants you to be satisfied with your new Snow
Blower. If for any reason you do not understand any part
of this manual or are not satisfied with the service
received, the following actions are suggested:

1.

Discuss the matter with your dealership service
manager making sure that person is aware of any
problems you may have and has had the opportunity
to assist you.

2.

If you are still not satisfied, seek out the owner or
general manager of the dealership, explain the
problem, and request assistance.

3.

For further assistance write to:

Land Pride Service Department

1525 East North Street

P.O. Box 5060

Salina, Ks. 67402-5060

E-mail address

[email protected]

35599

Right Side

Left Side

Introduction

Land Pride welcomes you to the growing family of new
product owners.

This Snow Blower has been designed with care and built
by skilled workers using quality materials. Proper
assembly, maintenance, and safe operating practices will
help you get years of satisfactory use from this machine.

Application

Land Pride offers the SBL2566, SBL2574, and SBL2584
Series of residential Snow Blowers ranging from 66" up
to 84" in width. They are equipped with a universal quick
attach mount for attaching to skid steers and tractors with
front loaders. These Snow Blowers are designed to
remove snow from parking lots, farm yards, feed lots,
driveways, walking paths, and sidewalks in residential
and commercial areas.

Land Pride’s unique patent-pending level run indicator
provides the operator with a clear, visible indication that
the Snow Blower is operating level. The auger, impeller,
and chute rotation are powered with individual hydraulic
motors. Adjustable skid shoes mounted on both sides
can be adjusted to carry the Snow Blower above hard
surfaces, loose gravel, and rocks to help increase the life
of the unit.

See “Specifications & Capacities” on page 31 and
“Features & Benefits” on page 32 for additional
information and performance enhancing options.

Using This Manual

This Operator’s Manual is designed to help familiarize
you with safety, assembly, operation, adjustments,
troubleshooting, and maintenance. Read this manual
and follow the recommendations to help ensure safe
and efficient operation.

The information contained within this manual was
current at the time of printing. Some parts may change
slightly to assure you of the best performance.

To order a new Operator’s or Parts Manual, contact
your authorized dealer. Manuals can also be
downloaded, free-of-charge, from our website at
www.landpride.com.

Terminology

See Figure 1: “Right” or “Left” as used in this manual is
determined by facing in the direction the machine will
operate while in use unless otherwise stated.

Definitions

IMPORTANT: A special point of information related
to the following topic. Land Pride’s intention is this
information must be read & noted before continuing.

NOTE: A special point of information that the
operator should be aware of before continuing.

Summary of Contents for SBL2566







































Reviews: