background image

2

RTR12 & RTA12 Series (Serial No. 884764-) Rotary Tillers   311-785M

2/11/21

Important Safety Information

Table of Contents

Transport 

Machinery Safely

Comply with state and local laws.

Maximum transport speed for 

implement is 20 mph. DO NOT 

EXCEED. Never travel at a speed 

which does not allow adequate 

control of steering and stopping. 

Some rough terrain require a 

slower speed. 

Sudden braking can cause a 

towed load to swerve and upset. 

Reduce speed if towed load is not 

equipped with brakes.

Use the following maximum speed 

- tow load weight ratios as a 

guideline:

20 mph

 when weight is less 

than or equal to the weight of 

tractor.

10 mph

 when weight is more 

than weight of tractor but less 

than double the weight of 

tractor.

IMPORTANT:

 Do not tow a load 

that is more than double the 

weight of tractor.

Use Safety 

Lights and Devices

Slow moving tractors, self-

propelled equipment, and towed 

implements can create a hazard 

when driven on public roads. They 

are difficult to see, especially at 

night.

Flashing warning lights and turn 

signals are recommended 

whenever driving on public roads. 

Practice Safe 

Maintenance

Understand procedure before 

doing work. Use proper tools and 

equipment, refer to Operator’s 

Manual for additional information.

Work in a clean dry area.

Lower the implement to the 

ground, put tractor in park, turn off 

engine, and remove key before 

performing maintenance.

Allow implement to cool 

completely.

Do not grease or oil implement 

while it is in operation.

Inspect all parts. Make sure parts 

are in good condition & installed 

properly.

Remove buildup of grease, oil or 

debris.

Remove all tools and unused 

parts from implement before 

operation.

These are common practices that may or may not be applicable to the products described in 

this manual.

Operate Equipment Safely

The operator must not use drugs 

or alcohol as they can change the 

alertness or coordination of that 

person while operating the 

equipment. The operator should, if 

he is taking over-the-counter 

drugs, seek medical advice on 

whether he can safely operate the 

equipment.

Keep bystanders away.

Start tractor with gearshift in park 

or neutral and park brakes set. Be 

aware hydraulics are live upon 

start-up and can move instantly. 

Dig Safe, Call 811.

Always contact your local utility 

companies (electrical, telephone, 

gas, water, sewer, and others) 

before digging so that they may 

mark the location of any under 

ground services in the area. Be 

sure to ask how close you can 

work to the marks they positioned.

Avoid contact with any over head 

utility lines or electrically charged 

conductors.

Summary of Contents for RTA12 Series





































Reviews: