background image

17

2/11/21

RTR12 & RTA12 Series (Serial No. 884764-) Rotary Tillers   311-785M

Land Pride

Section 2: Operating

Table of Contents

!

DANGER

Do not till across steep inclines exceeding 15 degrees. The 

action of the tines being forced down into the ground can 

cause the tractor to roll-over resulting in serious injury or 

death. Consult your tractor’s manual for acceptable inclines 

the tractor is capable of traveling across.

!

DANGER

Always disengage PTO before lifting tiller up and never 

operate tiller in the raised position. The tiller can discharge 

objects at high speeds resulting in injury or death.

!

DANGER

Do not use tiller as a working platform. The tiller is not 

properly designed or guarded for this use. Using tiller as a 

working platform can cause serious injury or death.

!

WARNING

Never allow children or other riders on the tractor or tiller. 

They can fall and be ran over causing serious injury or death.

!

WARNING

Do not use a PTO adaptor with a quick hitch. A PTO adapter 

will increase strain on the tractor’s PTO shaft resulting in 

possible damage to shaft and driveline.

!

WARNING

Use Rotary Tiller for its intended purpose only. Do not use 

tiller to lift or carry objects; to pull fence posts, stumps, or 

other objects; or to tow other equipment. Doing so can 

damage the tiller, cause serious bodily injury, or death.

!

WARNING

Always disengage PTO, put gear selector in park or set park 

brake, shut off tractor, remove ignition key, and wait for all 

moving parts to come to a complete stop before dismounting 

tractor.

!

WARNING

Always make certain driveline yokes are secured to the tractor 

PTO shaft and gearbox input shaft before engaging PTO. A 

loose driveline can slip off the end of a connected shaft while 

rotating and cause serious bodily injury or death.

!

WARNING

Do not allow anyone to operate this Rotary Tiller who has not 

been properly trained in its safe operation or anyone who is 

under the age of 16.

!

WARNING

Do not operate tiller with loose pins, bolts and nuts. Loose 

hardware can result in a serious breakdown causing bodily 

injury or death.

!

WARNING

Do not over speed PTO or machine breakage may result. Some 

tractors are equipped with multispeed PTO ranges. Be certain 

your tractor’s PTO is set for the tiller’s rated PTO speed. See 

Specifications & Capacities for rated PTO speed.

!

CAUTION

Make certain you are not working over any underground 

wiring, pipes, or other obstructions. If there is doubt, contact 

your local utility services so that they may mark the location 

of all underground utilities in the area. Be sure to ask how 

close you can work to the marks or flags they positioned.

IMPORTANT:  

Make sure all safety labels are in their 

proper location and in good condition before 

operation. Follow all directions on the safety labels.

IMPORTANT:  

Do not alter tiller in a way which will 

adversely affect its performance or reliability or use 

the tiller for a purpose for which it was not designed.

NOTE:  

To protect the parking stand from becoming 

bent while transporting and tilling the soil, always 

store it upside down in its mount.

Summary of Contents for RTA12 Series





































Reviews: