background image

30

RTR12 & RTA12 Series (Serial No. 884764-) Rotary Tillers   311-785M

2/11/21

Section 7: Features & Benefits

Table of Contents

Section 7: 

Features & Benefits

RTR12 Series

Features

Benefits

American made

American made means better parts availability. Many tillers are imported. 

Tractor HP range

42" & 50"
58" & 60"

74"

15-35 HP
20-40 HP
25-50 HP

Reverse tilling action

Reverse action ‘sucks’ tiller into ground, does not walk on top of hard ground like 
forward rotation tillers can.

3 year Gearbox Warranty

3 Years on housing, seals, & bearings. shows our confidence in the product.

42", 50", 58", 66" & 74" 
Working widths

A wide range of widths are available to meet specific customer needs.

6 1/2" Digging depth

For deep soil penetration.

Bent plate steel upper hitch

Plate steel is stronger than flat bar type hitch.

Clevis lower hitch

Provides additional strength and easy one person hook-up.

Offset Capabilities

Allows tiller to work closer to objects such as fence lines, buildings and trees.

Fits Land Pride Quick-Hitch

Allows for quick and easy one person hook-up. 
(Offset cannot be used with Quick-Hitch.)

Adjustable parking stand 

Allows for easy hook-up and storage.

Adjustable skid shoes 

Control depth with seven adjustments.

Formed and reinforced rear 
deflector

Keeps dirt in and leaves a level finish. Forming gives deflector additional strength.
Adjustable deflector allows for various finish results.

Front deflector

Front deflector is flexible to take the beating from rocks or debris.

4 ‘C’ shaped heat-treated 
tines per flange

‘C’ Shaped tines require less HP to move through the ground.

Solid steel rotor shaft

Solid steel shaft gives rotor extra strength.

15" Rotor swing diameter 

For deep tilling and turns the soil over faster.

Double lip seal on rotor bearing

Double lip seal helps keep the dirt out and the grease in.

Fully shielded slip-clutch driveline

Protects the gearbox and rotor shaft upon hitting obstructions. 
Slip-clutch saves having to replace shear-pins.

#80 Drive chain 
enclosed in oil bath

Heavy drive chain stretches less, and oil bath keeps wear to a minimum.

Stamped chain case cover

Stamped forming gives the chain cover strength.

Summary of Contents for RTA12 Series





































Reviews: