Land Pride Rear Blades RBT4596 Operator'S Manual Download Page 3 | Manualshive

Page: 3 / 38

background image

Table of Contents

1/13/21

©

Copyright 2021 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the

preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use

of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this

product at the time of its publication, and may not reflect the product in the future.

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

RBT4596 & RBT45108 Rear Blades 301-205M

Table of Contents

Important Safety Information . . . . . . . . . . . . . 1

Safety at All Times . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look for the Safety Alert Symbol . . . . . . . . . . . . . . . 1
Safety Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Application   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Using This Manual   . . . . . . . . . . . . . . . . . . . . . . . . . 8
Owner Assistance  . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Section 1: Assembly & Set-Up . . . . . . . . . . . . 9

Tractor Requirements . . . . . . . . . . . . . . . . . . . . . . . 9

Weight & Horsepower   . . . . . . . . . . . . . . . . . . . . . 9
Weight  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3-Point Hitch   . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Hydraulic Outlets  . . . . . . . . . . . . . . . . . . . . . . . . . 9

Torque Requirements  . . . . . . . . . . . . . . . . . . . . . . . 9
Tractor Shutdown Procedure   . . . . . . . . . . . . . . . . . 9
Assembly & Set-Up Safety   . . . . . . . . . . . . . . . . . . 10
Hitch, Frame & Blade   . . . . . . . . . . . . . . . . . . . . . . 10
3-Point Hook-Up  . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Standard 3-Point Hook-Up . . . . . . . . . . . . . . . . . 11
Quick Hitch Hook-Up . . . . . . . . . . . . . . . . . . . . . 11

Blade Offset Cylinder   . . . . . . . . . . . . . . . . . . . . . . 12
Blade Angling Cylinder  . . . . . . . . . . . . . . . . . . . . . 12
Blade Tilting Cylinder   . . . . . . . . . . . . . . . . . . . . . . 13

Section 2: Set-Up of Accessories . . . . . . . . . 14

Manual Offset, Angling and Tilting   . . . . . . . . . . . . 14
Gauge Wheel   . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Hydraulic Cushion Valve  . . . . . . . . . . . . . . . . . . . . 16
Hydraulic Selector Valve  . . . . . . . . . . . . . . . . . . . . 17
Skid Shoe  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
End Plates   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Section 3: Adjustments . . . . . . . . . . . . . . . . . 19

Safety First . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Blade Offset Adjustment . . . . . . . . . . . . . . . . . . . . 19

Manual Offset . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Hydraulic Offset . . . . . . . . . . . . . . . . . . . . . . . . . 19

Blade Angle and Reversing . . . . . . . . . . . . . . . . . . 19

Manual Angle and Reversing . . . . . . . . . . . . . . . 19
Hydraulic Angle and Reversing . . . . . . . . . . . . . 19

Blade Tilt Adjustments . . . . . . . . . . . . . . . . . . . . . 20

Manual Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Hydraulic Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Gauge Wheel Depth Adjustments . . . . . . . . . . . . . 20

Manual Depth Control . . . . . . . . . . . . . . . . . . . . 20
Hydraulic Depth Control . . . . . . . . . . . . . . . . . . . 20

Blade Pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Section 4: Operating Procedures . . . . . . . . . 21

Operating Checklist  . . . . . . . . . . . . . . . . . . . . . . . . 21
General Safety   . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Inspection After Hook-Up   . . . . . . . . . . . . . . . . . . . 22
Transport With Rear Blade   . . . . . . . . . . . . . . . . . . 22
Rear Blade Functions   . . . . . . . . . . . . . . . . . . . . . . 23

Grading   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Edge work   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Ditch Work  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Backfilling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Unhook Rear Blade  . . . . . . . . . . . . . . . . . . . . . . . . 23
Basic Operating Instructions  . . . . . . . . . . . . . . . . . 24
General Operating Instructions  . . . . . . . . . . . . . . . 24

Section 5: Maintenance & Lubrication . . . . . 25

Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Tractor Maintenance  . . . . . . . . . . . . . . . . . . . . . . . 25
Long-Term Storage  . . . . . . . . . . . . . . . . . . . . . . . . 25
Ordering Replacement Parts  . . . . . . . . . . . . . . . . . 25
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Blade Pivot Shaft  . . . . . . . . . . . . . . . . . . . . . . . . 26
Blade Tilt Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Front Pivot Shaft   . . . . . . . . . . . . . . . . . . . . . . . . 26
Moldboard and Blade  . . . . . . . . . . . . . . . . . . . . . 26
Ratchet Jack   . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Gauge Wheel Front Pivot  . . . . . . . . . . . . . . . . . . 27
Gauge Wheel Caster Tube . . . . . . . . . . . . . . . . . 27
Gauge Wheel Hub  . . . . . . . . . . . . . . . . . . . . . . . 27

Section 6: Specifications & Capacities  . . . . . 28
Section 7: Features & Benefits   . . . . . . . . . . . 29
Section 8: Troubleshooting  . . . . . . . . . . . . . . 30
Section 9: Torque Values Chart . . . . . . . . . . . 31
Section 10: Warranty   . . . . . . . . . . . . . . . . . . . 33

«
1
2
3
4
5
...
»

Summary of Contents for Rear Blades RBT4596







































Reviews:

No comments

Related manuals for Rear Blades RBT4596

Brand: Rath Pages: 3

Brand: GE Pages: 138

Brand: Gardena Pages: 13

Brand: DAKO Pages: 25

Brand: 3M ESPE Pages: 50

Brand: VACGEN Pages: 13

Brand: ParaBody Pages: 6

Brand: Sailmon Pages: 10

Brand: B&W Tek Pages: 12

Brand: b&o Pages: 46

Brand: Unitary products group Pages: 28

Brand: A&D Pages: 29

TOTAL KNEE 1900

Brand: Össur Pages: 58

Brand: MAKSIWA Pages: 155

Brand: IKEA Pages: 24

Brand: Yacht Devices Pages: 32

Evo TM/TSV2 Awning Wall Set

Brand: Zempire Pages: 2

Brand: GERATHERM Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands