Land Pride Rear Blades RBT4596 Operator'S Manual Download | Manualshive

Page: 19 / 38

background image

Section 2: Set-Up of Accessories

RBT4596 & RBT45108 Rear Blades 301-205M

1/13/21

15

Table of Contents

Hydraulically Controlled Gauge Wheel

Figure 2-2

24996

Customer to supply Quick
Disconnect Couplings.

Ratchet Jack Set-Up

1. Attach ratchet jack (#19) to the mounting lugs on the

gauge wheel arm (#3) and mounting bracket (#11)

with two 1" clevis pins (#20). Secure pins with hair pin

cotters (#21).

Hydraulic Cylinder Set-Up

1. Position hydraulic cylinder (#15) with ports on top as

shown. Thread 90 degree elbows (#13) into the two

ports and tighten.

2. Screw 116" long hydraulic hoses (#14) to the elbows

and tighten.

3. Thread hydraulic couplings (#18) to the other end of

hydraulic hoses and tighten. (Customer to supply

quick disconnect hydraulic couplings.)

4. Attach hydraulic cylinder to the lugs on the gauge

wheel with two 1" clevis pins (#17). Make sure

hydraulic ports are positioned on top and cylinder

base is located to the front as shown.

5. Secure clevis pins with hair pin cotters (#16).
6. Route hoses through the hose brackets located on

the top of the main frame and right side of the front

hitch. Connect hoses to tractor's hydraulic system.

IMPORTANT:

Attach cylinder base to the front

mounting lug. The base will interfere with the gauge

wheel arm if attached to the rear mounting lug.

Gauge Wheel

Kit Bundles

301-225A . . . . . . HYDRAULIC SINGLE GAUGE WHEEL
301-236A . . . . . . . .HYDRAULIC DUAL GAUGE WHEEL
301-281A . . . . . . . . .MANUAL SINGLE GAUGE WHEEL
301-282A . . . . . . . . . . MANUAL DUAL GAUGE WHEEL

Refer to Figure 2-2::

1. Attach gauge wheel mounting bracket (#11) to Rear

Blade frame with two 3/4"-10 x 10 1/2" GR5 hex head

bolts (#8) and 3/4" hex nuts (#10). Tighten nuts to

correct torque.

2. Insert gauge wheel hitch tube (#9) in gauge wheel

arm (#3).

3. Attach gauge wheel arm (#3) to mounting

bracket (#11) with 3/4"-10 x 10 1/2" GR5 hex head

bolt (#8) and 3/4" hex nut (#10). Tighten nut to correct

torque.

4. Insert gauge wheel caster assembly (single wheel

caster #1) or (dual wheel caster #2) in gauge wheel

arm (#3) and retainer washer (#4). Secure caster

assembly with 1/2" x 2 1/2" long roll pin (#5).

5. Attach center floating link (#12) to the front hitch with

1 1/4" x 1 3/4" hitch pin (#7). Secure with hair pin

cotter (#6).

«
...
17
18
19
20
21
...
»

Summary of Contents for Rear Blades RBT4596







































Reviews:

No comments

Related manuals for Rear Blades RBT4596

Brand: SAMCHULLY Pages: 48

Brand: Gallagher Pages: 6

medialon Showmaster Go

Brand: 7th Sense Pages: 9

Brand: iFIT Pages: 11

Brand: iHealth Pages: 8

Brand: JBL Pages: 38

Brand: JBSYSTEMS Light Pages: 32

Brand: JBM Pages: 12

Brand: Samson Pages: 2

Brand: M-system Pages: 4

Brand: Kattsafe Pages: 19

Brand: GGM gastro Pages: 3

Brand: Wartmann Pages: 56

Brand: ICON Pages: 24

Brand: Yardbird Pages: 12

Brand: Unitech Pages: 37

WEIDER SHAPE GLIDER WECR43062

Brand: ICON Health & Fitness Pages: 6

Brand: Duracell Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands